Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
© 2004 Directed Electronics, Inc 5. L LLi iin nne ee O OOu uut tt S SSw wwi iit ttc cch hh ( ((D DD2 222 220 005 55) )) - --three positions: s ssu uum mm L LL/ //R RR—left front and rear and right front and rear channels are summed. s ssu uub bb L LL+ ++R RR—set the switch to this position when using an additional D1200 amplifier connected in Parallel mode. s ssu uub bb 1 118 880 00° °°—set the switch to this position when using an additional D1200 amplifier connected in External Bridge mode. 6. G GGa aai iin nn - --controls amplifier sensitivity and is used to match the input level of the amplifier to the output level of the signal source. (front and rear on A1004 and D2205.) 7. B BBa aas sss ss E EEQ QQ - --allows 8dB additional bass boost (A802 and A1004). 8. X XX- --O OOv vve eer rr H HHP PPF FF, ,, F FFl lla aat tt, ,, L LLP PPF FF - --the HPF attenuates low frequencies and is used with mid-range speakers and tweeters. Full does not attenuate any frequencies and is for full range speaker systems. LPF attenuates high frequencies and is used for subwoofers. 9. X XX- --O OOv vve eer rr F FFr rre eeq qq - --adjusts the crossover point (50-500Hz) for the on-board active crossover. 10. R RRe eem mmo oot tte ee - --optional accessory which allows the level to be adjusted remotely (usually located for control by the vehicle’s driver). 11. S SSu uub bbs sso oon nni iic cc - --the OFF position takes the filter out of the system, the IN position places the the filter into the system (D2205). 12. S SSu uub bb G GGa aai iin nn - --subwoofer channel gain adjustment. 13. S SSt tta aat ttu uus ss L LLE EED DD - Will illuminate GREEN to indicate the amplifier is on and operating normally, and will be illuminated RED if the amplifier shuts down due to short circuit, DC offset, or overheating detected by onboard protection circuitry. 14. L LLE EED DD/ //F FFa aan nn - --allows connection of an o oop ppt tti iio oon nna aal ll LED light bar or o oop ppt tti iio oon nna aal ll cooling fan for the amplifier. 15. L LLP PPF FF - --sets high frequency limit of subwoofer channel (D2205). 16. B BBa aas sss ss E EEQ QQ - --allows 8dB additional base boost on sub channel (D2205). 17. S SSu uub bb I IIn nnp ppu uut tt/ //L LLi iin nne ee O OOu uut tt - --selects RCA jacks (4) (Sub/Line Out) as either Subwoofer Input or Line Output. © 2004 Directed Electronics, Inc 8 © 2004 Directed Electronics, Inc D2205 2 3 4 5 6 7 8 9 10 11 12 13 1 17 16 15 14 A1004 1 3 4 17 6 8 9 7 10 13 2 14 A802 1 3 4 6 8 9 7 13 2 14 FIGURE 1—AMPLIFIER CONNECTIONS — FRONT BLACK BLUE BLACK RED - + - + TO LEDs TO FAN FIGURE 5—LED/FAN HARNESS REAR PANEL CONNECTIONS 1. F FFu uus sse ees ss - --These fuses protect the 2. amplifier against internal electrical damage and are meant to protect the amplifier only. All other power connections should be fused at the source. The A802 uses 2-30A fuse, the A1004 uses 2-40A fuses, and the D2205 uses 3-40A fuses. 2. ( ((+ ++) )) 1 112 22 V VVo ool llt tt P PPo oow wwe eer rr - Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery. 3. W WWA AAR RRN NNI IIN NNG GG: ::Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 2. R RRe eem mmo oot tte ee T TTu uur rrn nn O OOn nn - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote turn on lead of the head unit or signal source. G GGr rro oou uun nnd dd - --Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+) 12 volt power wire. The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. S SSp ppe eea aak kke eer rr T TTe eer rrm mmi iin nna aal lls ss -Connect subwoofers to these terminals. (Refer to the Speaker Wiring Diagramssection of this guide.) © 2004 Directed Electronics, Inc 10 © 2004 Directed Electronics, Inc ESP® FEATURES AND CONTROLS A802 A1004 D2205 1 2 3 FIGURE 2—AMPLIFIER CONNECTIONS REAR These amplifiers incorporate an on-board Directed ESP® Engine. In addition to allowing menu-driven parameter adjustment*, operate with security products from Directed Electronics to incorporate advanced ESP2 features. Your dealer can use a Bitwriter® with Firmware version 1.906 or later to access these parameters. * Note: The ESP® features are obtained by using Bitwriter® and a 3 pin ESP® cable. While a Bitwriter® can only talk to one ESP®/ESP2 device at a time, multiple amplifiers can be set to respond to Arm/Disarm commands. Simply repeat the TX ID Learn procedure for each amplifier. When completed use a ...
Otros modelos de este manual:Avtousiliteli - A1004 (534.35 kb)
Avtousiliteli - D2205 (534.35 kb)