Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Ground (10.5-16V) 270 x 36 x 330 10.63 x 1.42 x 13 features and controls 18dB 0dB HPF LPF FULL HPF LPF FULL 18dB 0dB BASS BOOST X-OVER BASS BOOSTX-OVER CH 1/2 CH 3/4 4 ch amp PLA-4120 PLA-4120 9 electrical connections 2 ch amp • PLA-2230 • PLA-2260 PLA-2230 PLA-2260 10 PLA-4120 electrical connections PLA-4120 electrical connections 4 ch amp PLA-4120 11 stereo input connections 2 ch amp • PLA-2230 • PLA-2260 12 PLA-2230 PLA-2260 mono input connections 2 ch amp • PLA-2230 • PLA-2260 13 PLA-2230 PLA-2260 PLA-4120 14 4 ch amp PLA-4120 2/4 channel input connections PLA-4120 14 4 ch amp PLA-4120 2/4 channel input connections high level input connections 4 ch amp PLA-4120 4 CH floating ground connections PLA-4120 15 mono input connections 4 ch amp PLA-4120 4 CH mono input connections using low level inputs PLA-4120 16 2 CH mono input connections using low level inputs 17 Stereo Output ModePLA-2230 PLA-2260 Bridged Mono Output Mode speaker connections 2 ch amp • PLA-2230 • PLA-2260 17 Stereo Output ModePLA-2230 PLA-2260 Bridged Mono Output Mode speaker connections 2 ch amp • PLA-2230 • PLA-2260 speaker connections 4 ch amp PLA-4120 4 CH Output Mode PLA-4120 18 Bridged Dual Mono Output Mode speaker connections 4 ch amp PLA-4120 2 CH Stereo Output Mode with Mono Bridged Subwoofer Output PLA-4120 19 PLA-1200 20 MONO BLOCK AMPLIFIER PLA-1200 system wiring PLA-1200 20 MONO BLOCK AMPLIFIER PLA-1200 system wiring mounting and installation mounting Your new Pyle Chopper Series amplifier comes complete with all required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember that it is a high-power electronic device capable of generating high heat. For this reason, always choose a location in your vehicle which has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely. wiring tips When making electrical connections to your amplifier, please observe the following: Use at least 8 gauge wire for power and ground connections. Wire the amplifier directly to the car battery. For the ground connection, use the shortest possible wire to a good chassis ground point. Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna. fuses About power fuses: Pyle Chopper Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace the fuse in your Pyle Chopper Series amp, use a fuse of exactly the same type and rating. A different type or rating of fuse may result in damage or fire. No output. troubleshooting No output. troubleshooting protection circuitry The built-in protection circuitry in the Pyle Chopper Series amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the protection circuit is activated by any of these conditions, the Protection LED will be illuminated. If this occurs, carefully inspect the system to determine the source of the problem. • If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it. • If the shutdown was a result of an input overload, or speaker short circuit, be sure to correct the condition before restarting. The amplifier can be restarted by turning the remote power OFF and then ON again. Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the +12V and the Remote terminals must have +12v referenced to chassis ground. Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the amp). Briefly tap the center pin of each of the disconnected RCA plugs with your finger. This should produce a noise (feedback) in your speakers. Only one channel works. Confirm that all terminal strip connections are secure and tight. Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. If you are using the Low Level RCA input, reverse the input plugs at the amplifier (i.e., switch the L with the R). If the channels which is silent sw...
Otros modelos de este manual:Avtousiliteli - PYLE Chopper Series PLA-2260 (428.7 kb)
Avtousiliteli - PYLE Chopper Series PLA-4120 (428.7 kb)
Avtousiliteli - PYLE Chopper Series PLA-2260 (428.7 kb)