Votos - 2, Puntuación media: 4 ( )

Fabricar: Earthquake Sound Tamaño del archivo: 1.05 mb Nombre del archivo: Idioma del manual:

XOVER KNOB SETTING T2000W/4 MAX INPUT VOLTAGE BEFORE CLIPPING RCA LEVEL SPEAKER LEVEL 50Hz 90Hz 125Hz 170Hz 210Hz 250Hz FC6.2 Midrange FC6.2 Midrange FC6.2 Xover FC6.2 Xover FC6.2 Tweeter FC6.2 Tweeter FC6.2 Midrange FC6.2 Midrange FC6.2 Xover FC6.2 Xover FC6.2 Tweeter FC6.2 Tweeter AUTO ON RESET REMOTE ON LOW LEVELINPUTS: Low level inputs range of 0.2V to 7V RMS. This is where the front and rear RCA outputs from your head unit or other devices are inserted. with a AUTO SIGNAL SENSING: Please refer to page 3 for explanat ion of thi s feature. LEVELADJUST: Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume limiter for the system, preventing you from over driving the speakers or subwoofers. MODE SELECTOR: This feature tells the amplifier to run in either HIGH PASS, FULL RANGE or LOW PASS MODE R C A l i n e t h r o u g h t o c a s c a d e a n o t h e r amplifier. N o X o v e r point. 2-WAY 12dB/Oct VARIABLE XOVER: C o n t r o l t h e corresponding channels cutoff frequencies. This feature is disabled when in FULLRANGE This information applies to both channels 1/2 and 3/4 HIGH LEVEL INPUT: Speaker level inputs with a range of 0.5V to 17V RMS. POWER LED: When LED is on, it indicates that the amplifier is ON and f u n c t i o n i n g properly. PROTECTION (PROT) LED: If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details. Specifications Are Subject To Change Without Notice BASS BOOST: 0 - 18dB Bass Boost for use w i t h subwoofers. 12 13 T2000WD/1 SUBSONIC FILTER: For the vast majority of vehicles, peaks or dips occur at about 40Hz – around the frequency of a low bass guitar note. Use this control to correct that peak or dip. PHASE SHIFT: This 0 - 180° phase shift adjustment is for reversing the phase output with respect to its input. LOW PASS FILTER (LPF): This 50Hz - 300Hz lowpass filter blocks unwanted high f requencies for cleaner low-frequencies. 8-gauge speaker outputs REMOTE SUB LEVEL: Allows you to limit the bass output from a location of your choice. Using a screw mounted remote control. amplifier’s Two 30A fuses To car chassis / ground To remote turn on / trigger To battery positive (+) The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage to the amplifier (please refer to table for setting). 7.0V 17.0V 4.0V 10.0V 2.5V 5.0V 1V 1V SUB XOVER SETTING MAX INPUT VOLTAGE BEFORE CLIPPING RCA LEVEL SPEAKER LEVEL 50Hz 70Hz 150Hz 210Hz 240Hz 300Hz AUTO ON RESET REMOTE ON AUTO ON RESET REMOTE ON AUTO ON RESET REMOTE ON LOW LEVELINPUTS: Low level inputs range of 0.2V to 7V RMS. This is where the front and rear RCA outputs from your head unit or other devices are inserted. with a AUTO SIGNAL SENSING: Please refer to p a g e 3 f o r explanation of this feature. 0 - 10dB BASS BOOST CONTROL POWER LED: When LED is on, it indicates that the amplifier is ON and f u n c t i o n i n g properly. PROTECTION (PROT) LED: If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details. LEVELADJUST: Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume limiter for the system, preventing you from over driving the speakers or subwoofers. R C A l i n e t h r o u g h t o c a s c a d e a n o t h e r amplifier. N o X o v e r point. HIGH...

Descargar ahora

Introduzca dos números de la imagen: