Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
NOTE Use the set item and value operation buttons by following the instructions given on the Operation Manual of the Center Unit. 2 Select an amp number to operate Operate the desired set item with the Center Unit. Select the "AMP NO"/"AMP CONTROL NO" display. NOTE When the Center Unit is in the STANDBY mode, message "AMP OFF" is displayed and you cannot operate the set items. 3 Set an ID number of Amp to operate Set an amp’s ID number on the Center Unit. You can select an ID number of "0" to "7" of connected amps. 4 Select the AMP Control item for adjustment Select the desired set item on the Center Unit. 5 Adjust the AMP Control item You can set a value of each item on the Center Unit. The set items and their values are switched and displayed as follows. Display Range Adjustment Item "VOLT"/"CURR"/"TEMP"/"FAN" The amp state is displayed. "VOLT" Indicates the source voltage (V). "CURR" Indicates the current consumption (A). "TEMP" Indicates the internal temperature (°F/°C). "FAN" Indicates the rotation speed of the cooling fan in 3 steps: "FAST", "SLOW" or "OFF". "BAS F"/"BASS FREQ" 60/80/100/200 (Hz) Bass Center Frequency "BAS G"/"BASS GAIN" –15 — +15 (dB) Bass level "Q FA"/"Q FACTOR" Q1.00/Q1.25/Q1.50/Q2.00 Bass Q Factor "EXT"/"BASS EXT" ON/OFF When the bass extend is set to ON, low frequency response is extended by 20%. "TRE F"/"TREB FREQ" 10/12/15/17 (kHz) Treble Center Frequency "TRE G"/"TREB GAIN" –15 — +15 (dB) Treble level "VOL"/"VOL OFFSET" –20 — 0 (dB) Volume offset "AMP NO"/ "AMP CONTROL NO" 0 — 7 Select an ID number of the amp you use. 6 Exit AMP Control mode Releases the Amp Control mode by the Center Unit. NOTE When you have controlled the bass or treble of the sound using the Equalizer or DSP function of the Center Unit, and when you amplify the same frequency as that controlled by the Amplifier Control, the sound may be distorted due to an input overflow. Messages that may be displayed on the Center Unit When you are selecting an item with the Amp Control, an error status of the amplifier is displayed on the Center Unit. Display Informations "AMP . E-01"/"AMP . COND E-01" When the inside of the unit is overheating. "AMP . E-02"/"AMP . COND E-02" When the unit has failed and direct current voltage is generated to the speaker’s output. NOTE Turn the POWER switch Off and release the protection. If the error message continues, consult to the KENWOOD’s dealership. "AMP . E-03"/"AMP . COND E-03" When the speaker cord is shorted. When the speaker output is in contact with the vehicle ground. "AMP OFF" When you use the Amp Control in the Standby mode. NOTE Number "." on the display indicates the amp’s ID number. System examples . High-power 2-channel subwoofer system . 2-channel system .............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................. Left subwoofer (Bridged) CENTER UNIT CENTER UNIT Left speaker Right speaker Right subwoofer (Bridged) . 2-channel + Subwoofer system CENTER UNIT Left speaker (High pass) Right speaker (High pass) Subwoofer (L + R) (Bridged) . Tri-mode Principle of Tri-mode Method of frequency band division using a coil and capacitor…in case of 6dB/oct. slope. Subwoofer (L + R) (Bridged) (High pass) Coil (L): Passes low frequencies and blocks high frequencies. (Low pass) Capacitor (C): Passes high frequencies and blocks low frequencies. (High pass) Crossover Frequency LC 0 dB CENTER UNIT ...
Otros modelos de este manual:Avtousiliteli - KAC-PS521 (630.93 kb)
Avtousiliteli - KAC-PS621 (630.93 kb)
Avtousiliteli - KAC-X621 (630.93 kb)