Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
4 TABLE OF CONTENTS Features ………………………………………………….. 5 Front Panel Controls …………………………………...…. 6 Rear Panel Controls ………………………………………. 8 Protection ……………………….……………………....... 10 Setup ………………………………..…………………… 11 Connections …………………………………………..….. 13 Wiring…………………………………………………….. 15 Specifications…………..........……………………………. 17 INTRODUCTION Thank you for your decision to purchase Cerwin-Vega’s innovative new CV Series professional power amplifier! Engineered for superior sound reproduction, the CV Series line of professional amplifiers deliver top quality audio at an affordable price. The CV Series offers a standard of reliability and efficiency that makes them the perfect solution for every DJ, musician, and sound engineer. Welcome to a new level of professional quality sound performance! UNPACKING AND INSTALLATION Although it is neither complicated to install nor difficult to operate your amplifier, a few minutes of your time is required to read this manual for a properly wired installation and to become familiar with the amp’s features and how to use them. Please take care in unpacking your amp and do not discard the carton and other packing materials. They may be needed when moving your amp, and are required if it ever becomes necessary to return the unit for service. Never place the unit near a radiator, in front of heating vents, in direct sun light, in excessive humidity, or dusty locations to avoid damageto the amp and to guaranty it lives a long and reliable life. Connect your amp according to the description on the following pages. FEATURES The CV-5000 amplifier delivers the following power ratings. 2 x 1100 Watts at 8 ohm, 2 x 1800 Watts at 4 ohms and 2 x 2500 Watts at 2 ohms 2-channel, parallel or bridged mono operating modes for flexible application - 5000 Watts …and the following features. . Independent limiters for each channel reduce distortion. . Independent input level controls for each channel allow precision adjustments. . Precise signal and clip LED indicators to monitor performance, allow you to correct for overloading (clipping) condition. . Low-frequency filters (30Hz or 50Hz) remove rumble and subsonic frequency. . Twin-tunnel and two temperature-sensitivity forced-air cooling system to maintain a low, temperature working condition. . Balanced XLR or balanced 1/4-inch TRS Combination input connector for each channel and LINK ports. . 5-way output binding posts or Speaker connectors enable secure operation. . High-current toroidal transformer for absolute reliability. . Independent DC and thermal overload protection on each channel automatically protects amplifier and speaker. . The CV-5000 can be mounted in any standard 19” rack. front copy.jpg FRONT PANEL CONTROLS 1. Rack Mounting Ears Two front panel mounting holes are provided on each mounting ear. 2. Fan Vent CV-5000 amplifier is cooled by two rear-mounted fans. Cool air flows through the front fan filters, reducing the temperature of the inside components while forcing the heat out the rear vents. Never block these vents and keep them clean at all time. 3. AC Power Switch This switch controls the unit’s main power. 4. Signal Indicators These green and yellow LED will illuminate to indicate that a signal is present at the amplifier input, and that the signal is being amplified. 5. Clip Indicators These red LED will illuminate at the clipping threshold. If it lights frequently, you could be overloading the amplifier and a distorted signal is possibly being output. Under heavy clipping activity, lower the channel gain controls to reduce the risk of damage to your speakers and amplifier. 6. Active Indicators These blue LEDs indicate that AC power is connected and the amplifier is turned on. 7. Protect Indicators These red LED indicate that the channel is in Protect mode. When the channel goes into protect mode all output for that channel will turn off by output relay. The protect LED will light when overheating or other severe problems occur. This is to protect any speakers connected to the channel. These LEDs light for approximately five seconds whenever the amplifier is powered on, and fade slowly when the amplifier is powered off. This is normal operation. 8. Channel input level control These two 21-position controls adjust input level for their respective amplifier channels. In Bridged Mono Mode, only channel 1 input level control is used to adjust signal level. In Parallel Mode, both input level control are used to adjust signal level for their respective amplifier channels. At their fully counter-clockwise position, the signal is attenuated by more than 80dB. At their fully clockwise position, the signal is at unity gain. When 0 dBu of signal arrives at the input jacks and the Channel input level controls are set to their fully clockwise position, the amplifier delivers full power output. 502-HPA4000B-2121_01_Page_3 REAR PANEL CONTROLS 1. Fan This is a variable speed cooling fan. Cool air enters the amplifier through the fan ports loca...
Otros modelos de este manual:Avtousiliteli - CV-5000 (1.08 mb)