Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
This innovative system has been designed a 12 volts DC negative ground power supply. Easy installation with mounting hardware is provided. The PLMRA 400 has two input levels. The high or low impedance input can be connected to units which incorporate BTL circuity or common-ground types. (3) © (p nf CTT ^ ^ ^ C= c= — 3 CM/L 4 CH/ft — HIGH INPUT LEVEL to)) ■ (Cl CH/L 2CM/R LEVEL HIGH INPUT O 0 =3 iP ETr c= c= c= c= ©04-12V GND REMOTE*^ E ,-SPEAKERS- 4 CM/R 3CM/L tCH/R 1CH/L © © =3 =3 =3 =3 © In Gü CD Cü üü !©) kJ r—i- -—» (F Figure 1 1 FUNCTIONS l.POWER ON LED Lights up when the remote on system is energized. 2.INPII GAIN CONTROL Adjust high impedance input gain from 1 V to 300mV for best matching with PREAMP output for your car stereo. 3.LOW IMPEDANCE INPUT (HIGH LEVEL INPUT) This unit is provided with two terminal inputs (Front & Rear) for LOW impedance. If Your car stereo has four speaker outputs (LF,RF,LR,RR). Wire input as per FIG. 3 & FIG 3A. If your car stereo has two speaker outputs, please wire as per FIG 4 & FIG 4A. 4.HIGH IMPEDANCE INPUT (LOW LEVEL INPUT) This unit is provided with gold plated RCA input jacks for high impedance. Couple the RCA input with the car stereo output using RCA type connector cables. If your stereo has only left and right 2 channels outputs. You must use a Y-adaptor for connection (FIG 2). 5.POWER FUSE Power fuse protects both this amplifier and the automobile electrical system from wrong electrical conditions. 6.POWER SUPPLY TERMINAL Connct the +12V DC power supply wire into this terminal. By lugs and screws accessible at the panel of this amplifier (Fig. 5). A.BATT + Connect +12VDC power supply wire into this terminal from the (+) terminal of the battery. B.GROUND Ground terminal connects the ground wire from the chassis of the automobile. C.REMOTE Remote terminal connects the control wire which provides remote turn-on and off of the amplifier by the RADIO/CASSETTE players power antenna wire. 7.SPEAKERS TERMINALS Speakers can be easily connected to signal barrier strip. You may use 4 to 8 ohms speakers. Before connecting, please check speaker connection diagrams. 2 ELECTRICAL & AUDIO CONNECTIONS A. STEREO INPUT CONNECTION I.High impedance input. 2.Low impedance (BTL or Common Ground) Input a.Four Speaker Output Mode a-1. Floating Ground Type CAR STEREO Figure 3 3 ELECTRICAL & AUDIO CONNECTIONS a-2. Common Ground Type Figure 3A b.Two Speaker Output Mode b-1. Floating Ground Type Tf "F 'nf T’ "if "if "iF "ii—A Figure 4 4 ELECTRICAL & AUDIO CONNECTIONS b-2. Common Ground Type if ^ Eiï3 ‘ïf 'iT3 cïï3 ‘if ‘ii— __.«i-'u/a __POWER . . y . _ Nr^ E< — 3CH/L • 4 CH/fl HIGH INPUT LEVEL LOW TNPUT^ Ch/l* 2 CH/fi — LEVEL HIGH INPUT lo POO Figure 4A NOTE: High and low impedance input can not be used at same time. B. SPEAKER CONNECTION Connect the speaker output terminals to the corresponding speakers. (Figure 5) The speakers must be high quality and capable of handling high power. Separated return paths and strong wires are required. (Fig. 5) NOTE: This amplifier has built-in short circuit protection. If you mistakingly connect any speaker wires to ground, or positive power (+) and (-) Wires short together, the protection circuit will operate automatically and cut-off output. In case of this, you must switch OFF the whole system immediately double check speaker wire connections and isolation before switching on the amplifier again. 5 ELECTRICAL & AUDIO CONNECTIONS C. POWER CONNECTION FIG. 5 c= c= D= nr3 ^ CTP gir1 efr> eir3 "tT cn==^s ■ «ppakehs - V"^ 000 MAIN POWER LEAD — (TO CAR BATTERY POSITIVE TERMINAL) GROUND LEAD - (CONNECT TO A WELL GROUNDED METALLIC PART OF YOUR CAR ) REMOTE SWITCH - (CONNECT POWER ANT(ACC) LEAD WIRE OF YOUR CAR STEREO) w X- 4 RIGHT SPEAKER Da 3 LEFT SPEAKER IF =3 =3 1 LEFT SPEAKER 2 RIGHT SPEAKER Figure 5 1. Connect the B+12V pole of power supply directly to the battery (+) position terminal. 2. Connect the GND pole of power supply directly to the (-) negative ground battery terminal or car chassis...
Otros modelos de este manual:Avtousiliteli - PLMRA400 (472.97 kb)