Votos - , Puntuación media:
(
)
)
Fabricar: JL Audio
Tamaño del archivo: 368.42 kb
Nombre del archivo: 5ae81a85-a5b4-414a-ac09-27349aaa01e8.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
“My amplifier doesn’t turn on” Check the fuse, not just visually, but with a continuity meter. It is possible for a fuse to have poor internal connections that cannot be found by visual inspection. It is best to take the fuse out of the holder for testing. If no problem is found with the fuse, inspect the fuse-holder. Check the integrity of the connections made to each of the “+12VDC”, “Ground”, and “Remote” terminals. Ensure that no wire insulation is pinched by the terminal set screw and that each connection is tight. Check to make sure there is +12V at the “Remote” connection of the amplifier. In some cases, the turn-on lead from the source unit is insufficient to turn on multiple devices and the use of a relay is required. To test for this problem, jump the “+12VDC” wire to the “Remote” terminal to see if the amplifier turns on. If this does not work, proceed to the next step. “My amplifier’s output fluctuates when I tap on it or hit a bump” Check the connections to the amplifier. Make sure that the insulation for all wires has been stripped back far enough to allow a good contact area inside the terminal block. Check the input connectors to ensure that they all are making good contact with the input jacks on the amplifier. “My amplifier turns on, but there is no output” Check the input signal using an AC voltmeter to measure the voltage from the source unit while an appropriate test tone is played through the source unit (disconnect the input cables from the amplifier prior to this test). The frequency used should be in the range that is to be amplified by the amplifier (example: 50 Hz for a sub bass application or 1 kHz for a full range / high-pass application). A steady, sufficient voltage (between 0.2 and 8.0-volts) should be present at the output of the signal cables. Check the output of the amplifier. Using the procedure explained in the previous check item (after plugging the input cables back into the amplifier) test for output at the speaker outputs of the amplifier. Unless you enjoy test tones at high levels, it is a good idea to remove the speaker wires from the amplifier while doing this. Turn the volume up approximately half way. 5V or more should be measured at the speaker outputs. This output level can vary greatly between amplifiers but it should not be in the millivolt range with the source unit at half volume. If you are reading sufficient voltage, check your speaker connections as explained below. Check to ensure that the speaker wires are making a good connection with the metal inside the terminal block. The speaker wire connectors are designed to accept up to 8 AWG wire. Make sure to strip the wire to allow for a sufficient connection with the metal inside the terminal block. INSTALLATION NOTES: Use this diagram to document your amplifier’s switch and control positions. HP | Off | LPFilter ModeHigh-PassLow-PassFilter Frequency (Hz)Filter Frequency (Hz)Input Sens.Input Sens. CH 3&4Input Fromminmaxminmax601.2kHigh-Pass601.2k40150Low-Pass40150Off+12dBHigh-Level InputsHigh-Level InputsBass BoostHP | Off | LPFilter Mode1&2 | 3&4Off+12dBBass BoostChannel 3 & 4 ControlsCH 1 (Left)CH 3 (Left) ProtectChannel 1 & 2 ControlsPowerCH 2 (Right) LEFTRIGHTCH 4 (Right) Pre-OutsAmplifier Inputs INSTALLATION NOTES: INSTALLATION NOTES: Limited Warranty - Amplifiers (USA) JL Audio warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This warranty is not transferrable and applies only to the original purchaser from an authorized JL Audio dealer. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty. Warranty is void if the product’s serial number has been removed or defaced. Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you need service on your JL AUDIO product: All warranty returns should be sent to JL Audio ’s Amplifier Service Facility freight-prepaid through an authoriz...