Iniciar sesión:
Votos - 2, Puntuación media: 3.5 ( )

Manual de usuario Echo, modelo ECS-3301

Fabricar: Echo
Tamaño del archivo: 618.6 kb
Nombre del archivo: 2c69f556-a6c2-a504-7d00-8fc866d8b1d1.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


If any of the above symptoms appear, seek medical advice immediately. Cutting Safety • Do not cut any material other than wood or wooden objects. • For respiratory protection, wear an aerosol protection mask when cutting the wood after insecticide has been applied. • Keep others including children, animals, bystanders and helpers outside the hazard zone. Stop the engine immediately if you are approached. • Hold the unit/machine firmly with both hands. • Keep firm footing and balance. Do not over-reach. • Keep all parts of your body away from the muffler and cutting attachment when the engine is running. • Keep Bar/Chain below waist level. • Before felling a tree, the operator must be accustomed to the sawing techniques of the chain saw. • Be sure of pre-plan a safe exit from a falling tree. • While cutting, hold saw firmly with both hands with thumb firmly locked around front handle, and stand with feet well balanced and your body balanced. • Stand to the side of the saw when cutting never directly behind it. • Always keep the spiked bumper face to a tree, because the chain may suddenly be drawn into a tree. • Be alert against kickback (when saw kicks up and back at operator). Never cut with the nose of the bar. Maintenance safety • Maintain the unit/machine according to recommended procedures. • Disconnect the spark plug before performing maintenance except for carburetor adjustments. • Keep others away when making carburetor adjustments. • Use only genuine Tanaka replacement parts as recommended by the manufacturer. WARNING! Improper maintenance could result in serious engine damage or in serious personal injury. Transport and storage • Carry the unit/machine by hand with the engine stopped and the muffler away from your body. • Allow the engine to cool, empty the fuel tank, and secure the unit/machine before storing or transporting in a vehicle. • Empty the fuel tank before storing the unit/machine. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store unit/machine out of the reach of children. • Clean the unit carefully and store it in a dry place. • Make sure engine switch is off when transporting or storing. • When transporting in a vehicle, cover chain with chain cover. If situations occur which are not covered in this manual, take care and use good judgement. Contact your dealer if you need assistance. Pay special attention to statements preceded by the following words: WARNING! Indicates a strong possibility of severe personal injury or loss of life, if instructions are not followed. CAUTION! Indicates a possibility of personal injury or equipment damage, if instructions are not followed. NOTE! Helpful information for correct function and use. 3 custsvc@tanaka-ism.com Owner.s ManualECS-3301/3351 ECS-3301/3351 3. Assembly procedures WARNING! Never try to start engine without side case securely fastened. 1 . Remove chain bar clamp nuts. 2. Remove the side case (1) while pinching the rear part of the side case (1) .(Fig.1 -1) 3. Install, the chain bar (1) onto the bolts (2), then push it toward the sprocket (3) as far as it will go. Make sure that the boss of chain tension adjust bolt (4) fits into the hole of the bar (5). (Fig. 1-2) NOTE! Slightly move the bar back and forth and make sure the chain tension boss (4) fits into the hole (5) in the bar properly. 4. Confirm the direction of saw chain (1) is correct as in the figure, and align the chain on the sprocket. (Fig. 1-3) 5. Guide the chain drive links into the bar groove all around the bar. 6. Install the side case (1) onto the guide bar clamp bolts after inserting it on the alignment/locking tab on the engine case (2). (Fig. 1 - 1 ) Then fix the clamp nuts temporarily. 7. Raise the bar end, and tighten the chain (1) by turning the tension adjustment bolt (2) clockwise. To check proper tension, lightly lift up the center of chain and there should be about 0.51.0 mm clearance between bar and edge of drive link (3). CAUTION! • PROPER TENSION IS EXTREMELY IMPORTANT! (Fig.1 -4, 5) 8.Raise the bar end and securely tighten the chain bar clamp nuts with the box wrench. (Fig. 1 -4) 9.A new chain will stretch so adjust the chain after a few cuts and watch chain tension carefully for the first half hour of cutting. NOTE! Check the chain tension frequently for optimum performance and durability. CAUTION! • When the chain is excessively tightened, the bar and chain will be damaged rapidly. Conversely, when the chain is excessively loosened, it may get out of the groove in the bar. • Always wear gloves when touching the chain. WARNING! During operation, hold chain saw firmly with both hands. A single hand operation may cause serious injury. 4 custsvc@tanaka-ism.com Owner.s ManualECS-3301/3351 ECS-3301/3351 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Always run the engine on fue...

Otros modelos de este manual:
Benzo y sierras - ECS-3301 (618.6 kb)
Benzo y sierras - ECS-3301 (618.6 kb)
Benzo y sierras - ECS-3351 (618.6 kb)
Benzo y sierras - ECS-3351 (618.6 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría