Votos - 4, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Jonsered CS 2117 EL |
Resumen del manual
Always use approved safety gloves. Clean your chain saw regularly. Use approved face mask or safety goggles. Visual inspection. Do not use a coiled extension cord. Minimum wire cross-section: Maximum cable length: Voltage: 1,5 mm . 30 m 230 V CAUTION! Chain saws are dangerous! Careless or improper use can result in severe or fatal injury. SYMBOLS ON THE CHAIN SAW: CAUTION! Chain saws are dangerous! Careless or improper use can result in serious or fatal injury. Read operating instructions and make certain you understand them thoroughly before using the chain saw. The chain saw is double-insulated. Always use: • Approved helmet • Approved hearing protection • Approved safety goggles or face mask This product conforms to applicable CE directives. Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specified in «TECHNICAL SPECIFICATIONS» page 3 and on label. Do not expose saw to rain or moisture. Disconnect power in case of damage to power cable. Maximum permissible guide bar length. This product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product. IMPORTANT! BEFORE USING CHAIN SAW • Read operating instructions carefully. • Always observe the «Safe Use» recommendations on page 4. • Check chain and guide bar for correct assembly and adjustment. • Start the saw. • Do not start sawing until an adequate amount of oil has reached the chain. • Incorrect chain tensioning increases wear on chain, sprocket and guide bar, and may result in damage to these parts. • Improper use of power cable may lead to serious motor damage. IMPORTANT! Do not use a coiled power cable! Minimum wire cross-section: 1,5 mm . Maximum cable length: 30 m Voltage: 230 V CAUTION! The chain saw must not be modified in any way under any circumstances without the permission of the manufacturer. Use only original accessories. Unauthorized modifications and/or accessories may cause serious or fatal injury of the operator or others. 2 ENGLISHENGLISH CONTENTS Symbols 2 Important! Read before using chain saw 2 Contents 3 EC declaration of conformity 3 Technical specifications 4 Chain saw parts 5 Safe use 5 Starting and stopping 7 Daily inspection and maintenance 7 Kickback prevention 8 Chain brake with kickback guard 9 -Kickback guard inspection 9 -Manual chain brake function check 9 - Inertia chain brake function check 9 Mounting guide bar and adjusting chain 10 Chain catcher 11 Right hand guard 11 Slip clutch 11 Electronic overload protection 2000W 11 Cutting equipment 11 Chain and guide bar lubrication 12 - Chain oil 12 - Filling chain oil 12 - Checking automatic 12 chain lubrication system - Checking chain wear 12 Filing chain 13 Limbing 13 Crosscutting 14 Felling operations 14 - Danger zone 15 - Felling direction 15 - Clearing branches/Line of retreat 15 - Felling 15 EC DECLARATION OF CONFORMITY Husqvarna Norge AS, N-1708 Sarpsborg, Norway hereby declares that the following chain saws: Jonsered CS 2117EL and Jonsered CS 2121EL, with serial numbers starting at 54000001 and onwards, - are manufactured in compliance with EC Directive 98/37/EC (Machinery), EC Directive 73/23/EEC including amendments (Low Voltage Directive), EC Directive 89/336/EEC including amendments (Electromagnetic Compatibility Directive), and in accordance with annex V of Directive 2000/14/EC (Noise Emission in the environment by equipment for use outdoors) - are manufactured in compliance with the following harmonized standards: EN 50144-1, EN 50144-2-13, IEC 60745-1 and IEC 60745-2-13. Notified body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has: - carried out the EC type examination in accordance with the machinery Directive (98/37/EC) Article 8(2)(c) - issued EC type examination certifi cates No. 404/04/1038 - Jonsered CS 2117 EL and 404/04/1037 - Jonsered CS 2121 EL pursuant to machinery Directive 98/37/EC, Annex IV (4) The chain saw submitted is identical to the samples submitted for EC type examination. The measured and guaranteed sound power levels in accordance with Directive 2000/14/EC are set forth under Technical Data in the User’s Manual. Sarpsborg, 1th of October 2005 -------------------- Jan Hansen, President 3 ENGLISHENGLISH TECHNICAL SPECIFICATIONS Motor Rated voltage Rated output Frequency Slip clutch Electronic start control Electronic speed control Electronic overload protection Weight Without guide bar and chain With 14” guide bar and chain Chain lubri...
Otros modelos de este manual:Benzo y sierras - CS 2121 EL (693.29 kb)