Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Properly install front hand guard. This item can reduce injuries from kickback. Follow assembly instructions on page 6. Do not remove front hand guard. Do not replace front hand guard with substitute. The following steps will reduce the risk of kickback. • Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles. •Keep all safety items in place on saw. Make sure they work properly. • Do not overreach or cut above shoulder height. • Keep solid footing and balance at all times • Stand slightly to left side of saw. This keeps your body from being in direct line with chain. • Do not let guide bar nose touch anything when chain is moving (see Figure 1). Direction 90° Quadrant Do Not Let Guide Bar Touch Here Figure 1 - Kickback Hazard Example: Do Not Let Nose of Guide Bar Touch Object While Chain is Moving •Never try cutting through two logs at same time. Only cut one log at a time. • Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose). •Watch for shifting of wood or other forces that may pinch chain. • Use extreme caution when reentering a previous cut. • Use low-kickback chain and guide bar supplied with this chain saw. Only replace these parts with chains and guide bars listed in this manual. • Never use dull or loose chain. Keep chain sharp with proper tension. • Do not hand sharpen chain on automatic chain sharpening (Fast Sharp) models. Saw Maintenance and Kickback Safety Follow maintenance instructions in this manual. Proper cleaning of saw and chain and guide bar maintenance can reduce chances of kickback. Inspect and maintain saw after each use. This will increase the service life of your saw. Note:Even with proper sharpening, risk of kickback can increase with each sharpening. MAINTENANCE AND STORAGE OF CHAIN SAW 1. Unplug chain saw from power source • when not in use • before moving from one place to another • before servicing • before changing accessories or attachments, such as saw chain and guard 2. Inspect chain saw before and after each use. Check saw closely if guard or other part has been damaged. Check for any damage that may affect operator safety or operation of saw. Check for alignment or binding of moving parts. Check for broken or damaged parts. Do not use chain saw if damage affects safety or operation. Have damage repaired by authorized service center. 3. Maintain chain saw with care. • Never expose saw to rain. • Keep chain sharp, clean, and lubricated for better and safer performance. • Follow steps outlined in this manual to sharpen chain. •Keep handles dry, clean, and free of oil and grease. • Keep all screws and nuts tight. • Inspect power cord often. If damaged, have repaired by authorized service center. • Never carry chain saw by power cord. • Never yank power cord to unplug it. • Keep power cord from heat, oil, and sharp edges. • Inspect extension cords often and replace if damaged. 4. When servicing, use only identical replacement parts. 5. When not in use, always store chain saw • in a high or locked place, out of children’s reach • in a dry place • in a carrying case or with scabbard over guide bar Keep this manual for reference. It is your guide to safe and proper operation of this chain saw. 3 For more information, visit ® ® ELECTRIC CHAIN SAW CHAIN SAW NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Guide Bar Nose Tip or end of guide bar. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chance of kickback as required by ANS B175.1. Normal Cutting Position Stance used while making bucking and felling cuts. Notching Cut Notch cut in tree that directs fall of tree. Oiler Control System for oiling guide bar and chain. Power Head Chain saw without chain and guide bar. Also known as saw body. Pushback (Kickback, Pinch) Rapid pushback of chain saw. Pushback may occur if chain along top of guide bar is pinched, caught, or contacts a foreign object. Rear Handle Handle located at rear of saw body. Reduced Kickback Guide Bar Guide bar that reduces chance of kickback. Replacement Chain Chain that complies with ANS B175.1 when used with a specific saw. It may not meet ANS requirements when used with other saws. Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain. Spiked Bumper (Spike) Poin...
Otros modelos de este manual:Benzo y sierras - 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100 (1.03 mb)