Votos - 4, Puntuación media: 3.5 ( )

Fabricar: Makita Tamaño del archivo: 9.4 mb Nombre del archivo: DCS6400.pdf Idioma del manual:

CAUTION: Use only the following spark plugs: NGK BPMR 7A. Do not tighten the muffler screws when the engine is hot1 Check the muffler screws (10) for tightness. If they are loose, hand-tighten them. Important -do not overtighten! J Replacing the starter cable I Replacing the return spring Unscrew three screws (1). Remove fan housing (2). NOTE: The screws (1) are secured against falling out of the housing. CAREFUL! Injury hazard1 Do not unscrew screw (5) if the return spring is under tension. If the starter cable is to be replaced although it is not broken, it will be necessary to first de-tension the cable drum return spring (3). To do this, use the grip to pull the cable all the way out of the fan housing. Hold the cable drum with one hand, and with the other push the cable into the space (4). Carefully let the drum turn until the return spring is no longer under tension. Unscrew screw (5) and remove washer (6). Carefully remove the cable drum. CAREFUL1 Injury hazard! The return spring can pop out! Remove any cable pieces. Thread a new cable (dia. 1/8 (3 mm), length 38.6" (980 mm) as shown in the illustration (don't forget the washer (8)) and knot both ends as shown. Pull knot (9) into the cable drum (3). Pull knot (10) into the starter grip (7). Put the drum on its'spindle and turn it slightly until the return spring engages. Screw in and tighten screw (5) and washer (6). Guide the cable into the space (4) on the drum and use the cable to turn the drum two turns clockwise. Hold the cable drum with your left hand and with your right hand untwist the cable, pull it tight and hold it. Carefully release the cable drum. The spring will wind the cable around the drum. Repeat three or four times. The starter grip should now be held upright on the fan housing. NOTE: With the cable pulled all the way out, it must still be possible to turn the pulley another 1/4 turn against the return spring. CAUTION: Danger of injury! Secure the cable grip when pulled out1 It will whip back if the cable pulley is released by accident. Replacing the return spring Disassemble the fan housing and cable drum (see above). CAUTION: Danger of injury1 If the spring is broken it may pop out! Replacement return springs are supplied pretensioned in the cable drum. CAUTION -the spring can pop out. If it does, it can be put back in as shown in the drawing. Before installation in the fan housing, lightly grease !he new return spring (11) with multipurpose grease (order no. 944 360 000). Install the cable drum and fan housing (see above). Mounting the fan housing Put the fan housing (13) on. Press the screws (14) into their holes. Lift the engine hood (15) slightly and use your thumb to hook in the tab (16) on the fan housing. Straighten outthe fan housing, push lightly against the saw and pull the starter grip until the starting mechanism catches. Tighten screws (14). Cleaning the cylinder area Remove the filter hood and air filter. Remove the spark plug cap and unscrew the spark plug. Press in the starting valve and activate the chain brake. Push the cable cutout and ignition cable out sideways. Unscrew the two rearmost screws on the cover. Unscrew the screws on the handguard pivot and remove the bushing. Lift the cover out of the air intake guide and remove. IMPORTANT: Put the air filter back on and fasten it. Insert the spark plug and hand-tighten. Put the spark plug cap on the plug and pull out the starting valve. Remove the fan housing and remove the air guide. CAUTION: To prevent eye injury, always wear eye protection when cleaning the filter with compressed air! The entire area (17)can now be brushed clean or cleaned with compressed air. A bottle brush can come in handy for cleaning out the cylinder ribs. I 17 Replacinglcleaning the spark arrester screen The spark arrester screen should be checked and cleaned regulary. Loosen the screw (18) and remove the spark arrester screen (19). Caution: Do not use sharp or pointed objects for screen cleaning. Damaged or misformed screen wires may result. Reassembly the spark arrester screen and'tighten the screw. Instructionsfor periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must be carried out by a MAKITA service centre. General Chain saw Saw chain Chain brake Guide bar Starter cable Before each start Saw chain Guide bar r Every day Every 3 months Chain lubrication Chain brake OFF switch, Safety locking button, Throttle lever Fuelloil tank caP Air filter Guide bar Guide bar support Idle speed Fan housing Cylinder area Spark plug Muffler Chain guide Suction head Fuel, oil tanks Chain saw Chain saw ...

Descargar ahora

Introduzca dos números de la imagen: