Iniciar sesión:
Votos - 3, Puntuación media: 4.3 ( )

Manual de usuario Electrolux, modelo Electramac 95390017700

Fabricar: Electrolux
Tamaño del archivo: 3.79 mb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


These situations can be avoided by ensuring correct chain tension (Refer to chapter “D. Assembly/disassembly”). REAR HAND GUARD This acts to protect(fig.5) the hand in the case of chain breaking or derailing. 2,3,6,7,8,9,12 D. ASSEMBLY / DISASSEMBLY BAR AND CHAIN ASSEMBLY Assembly methods change according to the type of your machine- so please take care to refer to the illustrations and machine type marked on the label (A- Legend – 9 [ES15 / ES16 / ES18] ), Take great care when assembling to ensure this is performed correctly. FOR ES 15 / ES 16 FOR ES 18 1. Control that the chain brake is not activated. If so, deactivate it. 2a. Unscrew the bar retaining nuts and remove the chain cover. 2b. Unscrew the bar retaining knob and remove the chain cover. 3a. Mount the bar on the bar retaining screws pushing it as far backward towards the pinion as possible. 3b. Mount the bar on the bar retaining screw pushing it as far backward towards the pinion as possible. 4. Oil the chain, then position it over the pinion, making it slide into the bar guide groove, beginning with the upper part. Attention! Control that the sharp side of the cutting teeth face in a frontward direction on the upper part of the bar; Set the chain tensioner pin in the chain tensioner pin housing. Mount the chain cover making sure that the drive teeth of the chain are engaged in the pinion and in the guide groove. 5a. Close the bar retaining nuts, screwing by hand. 5b. Screw the bar retaining knob loosely tightened. 6a. To spread the chain screw the chain tensioner screws in a clockwise direction, to loosen tension, screw in an anti-clockwise direction (when performing this operation maintain the bar nose raised upwards) 6b. To spread the chain screw the chain tensioner knob in a clockwise direction, to loosen tension, screw in an anti-clockwise direction (when performing this operation maintain the bar nose raised upwards) 7 Spread the chain until the tension is correct; that is, when the chain is pulled upwards, the drive tooth rise to the same level as the bar. (the chain must never droop on the underside of the bar) 8a. Tighten the bar retaining nuts using an appropriate tool. 8b. Tighten the bar retaining knob strongly. Tensioning the chain too tightly will overload the motor and cause damage, insufficient tension can provoke chain derailing, whereas a chain tightened correctly provides the best cutting characteristics and prolonged work life. Check the tension regularly because the chain length tends to stretch with use (especially when the chain is new; after the first assembly, the chain tension must be controlled after 5 minutes machine operation); in any ENGLISH - 6 case do not tighten the chain immediately after use, but wait until it cools down. In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nuts / knob before adjusting the chain tensioning screw/knob ; adjust the tension and tighten the bar retaining nuts /knob accordingly. E. START-UP AND ARREST 1,4,5,6,7,8,9,11,12,13 Start-up: grip both handles firmly, release the chain brake lever, press and maintain the switch block pressed in, then press the switch (at this point the switch block can be released). Arrest: The machine will stop whenever the switch is released. In the case where the machine does not s...

Otros modelos de este manual:
Benzo y sierras - Electramac 312 (3.79 mb)
Benzo y sierras - Electramac 314 (3.79 mb)
Benzo y sierras - Electramac 330 (3.79 mb)
Benzo y sierras - Electramac 416 (3.79 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría