Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
ON/STOP SWITCH (SIDE VIEW) STOP _ ON 1. Move ON/STOP switch to the ON position. 2. Slowly press primer bulb 6 times 3. Pult choke/fast idle lever out to the full extent (to the FULL CHOKE position) 4. Pulithe starter rope sharply 5 times with your nght hand. Then, proceed to the next step. NOTE: If the engine sounds as if it is trying to start before the 5th putl, stop pulling and immediately proceed to the next step. 5. Push the choke/fast idle lever in to the HALF CHOKE osition. CHOKE/FA_T IDLE LEVER o_EW) Ch fast idle lever OFF HALF FULL 8. Pul} the starter rope sharp}y with your right hand until the engine starts 7. Altow the engine to run for approximate- Iy 30 seconds Then, squeeze and re- tease the throttle trigger to allow engine to return to idle speed STARTING A WARM ENGINE 1. Move ON/STOP switch to the ON position 2. Slowly press primer bulb 6 times. 3. Puli the choke/fast idle lever out to the HALF CHOKE position. 4-. Pull the starter rope sharply with your right hand unfl_ the engine starts. 5. Squeeze and release throttle trigger to allow engine to return to idle speed. DIFFICULT STARTING (or 8tarring a flooded engine) The engine may be flooded with too much fuel if it has not started after fO pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP sw_tch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723. CHAIN BRAKE _I, WARNING: tf the brake band is worn too thin it may break when the chain brake is triggered With a broken brake band, the chain brake will not stop the chain The chain brake should be replaced by an authorized service dealer if any part is worn to less than O O2O" (05 mm) thick. Repairs on a chain brake should be made by an authorized service dealer Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. • This saw is equipped with a chain brake The brake is designed to stop the chain if kickback occurs • The inertia-activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement) • If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible • When cutting with the saw, the chain brake must be disengaged Braking function control CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the en gine runmng. Place the saw on firm ground Grip the rear hand}e with your right hand and the front han dle with your left hand. Apply full throttle by fuily depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle The chain should stop immediately Inertia activating function control _WARNING: When performing the following procedure, the engine must be turned off G rip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14" (35 cm) above a stump or other wooden surface Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate 10 sloping terrain. Use a plumb or level to determine the dLrection of tree Lean. • Weight and branches on one side. • Surrounding trees and obstacles Look for decay and rot. if the trunk is rotted, IMPORTANTPOINTS • Check chain tension before first use and after f minute of operation. See CHAIN TENSION Lnthe ASSEMBLY section • Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. • Stop the saw ff the chain strikes a foreign object. Lnspect the saw and repair or replace parts as necessary. • Keep the chain out of dirt and sand Even a small amount of dirt will quickly dult a chain and thus increase the possibil*ty of kickback. • Practice cutting a few small logs using the foIIowing techniques to get the "feeF of using your saw before you begin a major sawing operation. • Squeeze the throftle trigger and allow the engine to reach full speed before cutting. • Begin cutting with the saw frame against the log. • Keep the engine at full speed the entire time you are cutting. • ALlow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or engine can result. • Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting Load, u...
Otros modelos de este manual:Benzo y sierras - 1975 (808.29 kb)
Benzo y sierras - 2155 (808.29 kb)