Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Empty the fuel tank and clean the inside. Sharpen the chain and check its tension and condition. Check the drive sprocket for excessive wear and replace if necessary. Clean the carburetor compartment. Empty the oil tank and clean the inside. Clean the starter units air intake. Clean the air filter. Replace if necessary. Check all cables and connections. Check that nuts and screws are tight. Check that the stop switch works correctly. Check that there are no fuel leaks from the engine, tank or fuel lines. On chain saws with a catalytic converter, check the cooling system daily. 38 – English TECHNICAL DATA Technical data CS 2152 CS 2153 Engine Cylinder displacement, cu.in/cm3 3,15/51,7 3,06/50,1 Cylinder bore, inch/mm 1,77/45 1,74/44,1 Stroke, inch/mm 1,28/32,5 1,28/32,5 Idle speed, rpm 2700 2700 Power, kW/hp @ rpm 2,4/3,3 @ 9000 2,6/3,5 @ 9600 Ignition system Manufacturer of ignition system SEM SEM Type of ignition system CD CD Spark plug NGK BPMR 7A/ NGK BPMR 7A/ Champion RCJ 7Y Champion RCJ 7Y Electrode gap, inch/mm 0,02/0,5 0,02/0,5 Fuel and lubrication system Manufacturer of carburetor Zama Zama Carburetor type C3-EL32 C3-EL32 Fuel tank capacity, US pint/litre 1,06/0,5 1,06/0,5 Oil pump capacity at 9,000 rpm, ml/min 5-12 5-12 Oil tank capacity, US pint/litre 0,59/0,28 0,59/0,28 Type of oil pump Automatic Automatic Weight Chain saw without bar or chain, empty tanks, 11,0/5,0: CS 2152, CS 2152 C 11,2/5,1: CS 2153, CS 2153 C lb/kg 11,2/5,1:CS 2152 W, CS 2152 WH, 11,5/5,2: CS 2153 WH, CS 2152 CWH CS 2153 CWH Chain/bar Standard bar length, inch/cm 13"/33 13"/33 Recommended bar lengths, inch/cm 13-20"/33-50 13-20"/33-50 Usable cutting length, inches/cm 12-19"/31-49 12-19"/31-49 Pitch, inch/mm 0,325/8,25 0,325/8,25 Thickness of drive links, inch/mm 0,050/1,3 0,050/1,3 0,058/1,5 0,058/1,5 Drive sprocket type/teeth Rim/7 Rim/7 Chain speed at max. power, m/sec 17,3 18,5 English – 39 TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Jonsered chain saw models CS 2152 and CS 2153. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B 175.1–2000. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose. The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction. As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar. Bar and chain combinations Bar Chain Length, inch Pitch, inch Gauge, inch Max. nose radius Type Drive link count 13 0,325 0,050 10T Jonsered H30 56 15 0,325 10T 64 16 0,325 10T 66 18 0,325 10T 72 20 0,325 10T 78 13 0,325 0,058 10T Jonsered H25 56 15 0,325 10T 64 16 0,325 10T 66 18 0,325 10T 72 20 0,325 12T 78 Note: For the saw chains above (if available) you are free to choose between 0,050" or 0,058" gauge drive links for the corresponding bar, see the table below. 0,050"/1,3 mm H30 0,058"/ 1,5 mm -H25 Saw chain filing and file gauges 40 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2009 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. Jonsered must warrant the emission control system on your small nonroad engine for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. Your emmission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Jonsered will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor. MANUFACTURER. .... S WARRANTY COVERAGE The 2009 and later small nonroad engines are warranted for two years. If any emission related part on you engine (as listed above) is defective, the part will be repaired or replaced by Jonsered. OWNER. .... S WARRANTY RESPONSIBILITIES As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator. s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small nonroad engine, but Jonsered cannot deny warranty s...
Otros modelos de este manual:Benzo y sierras - CS 2152 EPA III (2.31 mb)