Votos - 5, Puntuación media: 3.6
(
)
)
|
Resumen del manual
1 Assembly Chainsaw assembly and preparation ..............................… 2 Compatible chainsaws and sprockets ……………………… 2 RIPSAW assembly ….........................................................…. 3 Dimension plate assembly …........................................…. 4 Guide beam assembly.......................................….……… 5 End clamp assembly …………………………………………….. 6 Blades Changing blades …..............................................……….. 11 Tracking blades Drive wheel …………………………… …………….. 12 Idler wheel ……………………… ……………… 12 Sharpening blades …....................................................… 13 Carbide guide adjustment/replacement ……………………………… 11 Log capacity ……………...............................................………… 14 Sawing wood ………….......................................................……. 15 Parts diagrams Front covers ………..........................................…… 7 Ripsaw ………………...............…............................……… 10 End clamps ………………………………………………….. 6 Parts list …….........................................................……………… 8-9 Warranty / Guarantee .............................................…………. 16 SSaaffeettyy iinnssttrruuccttiioonnss Proper operation of The RIPSAW is essential to avoid serious personal injury to the operator and bystanders. Keep hands, feet, face, and clothing away from all moving parts of the saw at ALL TIMES. Read through the entire manual thoroughly. If you are uncertain of any procedures in this manual, please consult S.I.R. for assistance. (256) 728-3070. 1. Always wear eye and ear protection while operating the RIPSAW or chainsaw. 2. If you plan to rest the log on trestles, be sure that they are steady and at a comfortable height for you to work with. 3. Before starting the saw, make sure that the log is secure and that it will not move while you are pushing the saw through it. 4. The use of the RIPSAW is a one-person operation. If you should require assistance in moving logs or cut lumber, ensure that the person is wearing protective equipment and keep at a safe distance from the sawmill while it is in operation. 5. For re-fueling gasoline powered sawmills, extinguish all smoking materials, stop the engine and allow it to cool. prepare the gas/oil mixture as instructed in your chainsaw owner’s manual. 6. Keep the blade guard closed until just before starting a cut. 7. Keep all spectators at least 20 feet away from the milling operation. 1 SSttiihhll CChhaaiinnssaaww aasssseemmbbllyy//pprreeppaarraattiioonn (When providing your own chainsaw) 1. Clean the mounting surface on the powerhead and remove the following parts. (Retain these parts for future use.) NOTE: Be sure that the chain brake is disengaged. a. 2 bar nuts b. chain/sprocket cover c. bumper spike, bolts and nuts which fasten it d. snap ring from crank shaft e. large washer from crank shaft 2. A 7 tooth spur gear sprocket is required to run the sawmill with some Stihl models. 3. Replace the sprocket if necessary. (See chart below) 4. Place small washer onto crankshaft. 5. Secure washer with the snap ring you previously removed. 6. Apply liquid gasket material to shaded area in diagram below. 7. Adjust bar oiler flow to a minimum, by inserting a small screwdriver into slot located on the bottom of the powerhead and turning it counterclockwise. 8. Attach powerhead to the RIPSAW using the instructions on page 3. MMAAKKEE SSUURREE BBAARR OOIILLEERR CCOONNTTAAIINNSS AANN AAMMPPLLEE SSUUPPPPLLYY OOFF OOIILL.. FFAAIILLUURREE TTOO DDOO SSOO WWIILLLL RREESSUULLTT IINN RRIIPPSSAAWW GGEEAARR FFAAIILLUURREE.. Compatible chainsaws for adaptation to the Ripsaw portable sawmill Stihl models: 028, 029, 034, 036, 036PRO, 038, 039, 044, 046, 064, and 066, MS290, MS360, MS380, MS390, MS440, MS460, MS660, E20 and MSE220 electrics Jonsereds models: 2065, 2165, 2071 Husquvarna models: 365 , 371, 395 Stihl sprocket part numbers Stihl 026 1121 640 2003 Stihl 026 w/adj. oiler 1121 640 2004 Stihl 028, MS280 1118 640 2003 Stihl 029, MS290 1125 640 2004 Stihl 034 1125 640 2004 Stihl 036, MS360 1125 640 2004 Stihl 038, MS380 1119 640 2000 Stihl 039, MS390 1125 640 2004 Stihl 044/046, MS440, 460 1128 640 2000 Stihl 064/066, MS660 1122 640 2002 2 Text Box: Apply liquid gasket here Text Box: 7 tooth spur sprocket Text Box: AAsssseemmbbllyy iinnssttrruuccttiioonnss RIPSAW accessories are located inside guide beams 1. Release blade tension by loosening tension bolt. 2. Loosen and remove cover knobs from front cover plates. 3. Remove Drive cover plate from sawmill. (plate with RIPSAW decal) 4. Remove bar nuts from chainsaw. 5. Position chainsaw studs through adapter block on RIPSAW. 6. Rotate sprocket to engage drive mechanism. 7. Re-install bar nuts into recesses in adapter and tighten them securely. 8. Re-install Drive cover plate. (Be sure that locating pins are through the holes in cover plates before installing and tightening cover knobs.) 9. Re-install cover knobs and tighten securely. 10. Tighten the tension ...
Otros modelos de este manual:Benzo y sierras - 029, 039 (766.45 kb)
Benzo y sierras - 28 (766.45 kb)
Benzo y sierras - 46 (766.45 kb)