Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
mute the microphone during a conversation. INTERCOM: Used to make or receive VOICE CALL (KX-T7750 only): Used to intercom calls. receive a notification via monitor in place of ringing. FWD/DND (Call Forwarding/Do Not Disturb): Used to perform Call Forwarding 7 8 AUTO DIAL/STORE: Used for speed or Do Not Disturb. dialing or storing program changes. FLASH/RECALL: Used for External Feature REDIAL: Used to redial. Access or to disconnect the current call and make another call without hanging up. –8– 5 Location of Controls 9 DIALING BUTTONS WITH BACKLIGHT (KX-T7731/36): Dialing buttons are backlit when (1) you receive a call, (2) during a conversation, or (3) when BGM is activated at your phone. 10 11 12 TRANSFER: Used to transfer a call to another party. HOLD: Used to place a call on hold. SP-PHONE (Other than KX-T7750): Used for the handsfree operation. MONITOR (KX-T7750 only): Used for handsfree dialing. You can monitor the other party's voice handsfree. 13 NAVIGATOR KEY (KX-T7730/7731/7735/7736): Used to adjust the volume and the display contrast, or select desired items. VOLUME KEY (KX-T7720/7750): Used to adjust the volume. 14 Programmable Feature (PF) Button: Used as an One-Touch Dialing button (Button assignment is required). Initial Settings 15 16 17 18 Flexible Outside (CO) Line Button: Used to make or receive an outside call. Pressing this button seizes an idle outside line automatically. (Button assignment is required.) Also used as feature buttons. (Button assignment is required.) PAUSE: Used to insert a pause during dialing. MESSAGE: Used to leave a message waiting indication, or call back the party who left the message waiting indication. Message/Ringer Lamp: The Message/ Ringer lamp informs you visually that you have a message or a call. When you receive a call, the lamp flashes depending on the ringing pattern. When the ringing pattern is set to Single (Slow flash), Double (Moderate flash), or Triple (Rapid flash) in your PBX, the lamp flashes. When the other ringing patterns are set in your PBX, the lamp may not flash. (e.g., S-Double, Call Waiting Tone1). When someone has left you a message, the lamp is lit continuously. Speaker volume * While on-hook or during a conversation SP-PHONE Press SP-PHONE. Press Up or Down. Ringer volume/Backlight illumination 2 0 1 RINGER BACKLIGHT Slide the lever of the RINGER Volume Selector and BACKLIGHT Illumination Selector to the desired setting. Handset/Headset volume * While using the handset or headset Press Up or Down. Display contrast * KX T7730/7731/7735/7736 Press Left or Right. BACKLIGHT SW POSITION 2 1 0 LCD backlight HIGH LOW OFF DIALING BUTTONS backlight AUTO AUTO OFF AUTO: The backlight shines only during operation. * The above settings may return to default settings if the telephone line cord is disconnected, or the main unit's power is interrupted. –9– Wall Mounting 1 Pull down the handset hook until it locks, so the tab holds the handset. 2 1 2 Remove the attached stand. 3 Mount the unit on the wall. To temporarily place the handset down during a conversation, hook it over the top edge of the phone as shown. Connection CAUTION Ensure the cord is inserted in the groove to prevent damage to the connector. To the main unit ( The telephone line cord ) (included) < Back view> TO MAIN UNIT /PABX Headset * KX-T7735 model illustrated on this page. – 10 – Exhibit J - Customer Information This equipment complies with Part 68 of the ACTA rules and the requirements adopted by the ACTA. On the exterior of the cabinet of this equipment is a label that contains, among other information, a product identifier in the format ACJGTB-32973-MF-E/ACJGTB-43121-MF-E. If requested, this number must be provided to the telephone company. ACTA Registration Number (KX-TA624): ACJGTB-32973-MF-E (KX-TA1232): ACJGTB-43121-MF-E Ringer Equivalence Number (REN): 0.4B Facility Interface Code (FIC): 02LS2 Service Order Code (SOC): 9.0F USOC Jack Type (KX-TA624): RJ11 (KX-TA1232): RJ11 and RJ14C A FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant. See Installation Instructions for details. If this equipment KX-T7731/36 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to it's facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice so you can make the necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment KX-T7731/36, ...