Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
User’s manual 11. Quick Start Guide To purchase replacement battery packs, visit us on the web at or call VTech Communications, Inc. at 1-800-595-9511. In Canad a , c ont ac t VTe c h Telecommunications Canada Ltd. at or 1-800-267-7377. Parts checklist: • Before using this telephone, you must read Important safety instructions on page 37. Base unit Handsets (2) Charger Belt clips (2) Batteries (2) Charger power adaptor Telephone line cord Base power Adaptor Wall mount bracket Quick Start Guide User’s manual Getting started Installation Choose location For maximum performance of your cordless telephone system: 1. Choose a central location for your base unit. 2. Install your phone(s) as far away as possible from any other cordless (wireless) device such as cordless telephones, 802.11 wireless router (for example, WiFi). 3. Install your phone(s) as far away as possible from other electronic equipment such as microwave ovens, televisions, computers, etc. 4. Install your telephone equipment away from heat sources and direct sunlight. 5. Avoid excessive moisture, dust or extreme cold. Install handset battery 1. 2. 1. Align the two holes in the plug with the socket pins, matching the red and the black connectors, then snap the plug into place. 2. Place the battery in the compartment with the wires in the upper right corner. 3. Replace cover by sliding it upwards until it clicks into place. 4. Be sure to charge the battery for 16 hours before using your phone. • Use only the provided VTech battery, or equivalent. • Place the handset in its base or charger when not in use to ensure optimum performance. • if you need to install your phone within the same room as other cordless phones or wireless products, you may need to select a different channel for your router and or change the channel on your phone’s handsets. 1 3 • Connect the power and telephone line cords to the underside of the base as illustrated • Plug the AC adaptor into an electrical outlet If the battery has not been charged, place the handset in the base or charger, and allow it to charge for at least 16 hours • Be sure to use an electrical outlet not controlled by a wall switch Installation Connect power to base unit/chargers 1 Plug the power adaptor into an electrical outlet not controlled by a wall switch, and the connector into the bottom of the base unit 2 Choose the location for your charger, and plug its power supply into an electrical outlet To power outlet To telephone outlet Connect to phone line Plug one end of the telephone line cord into the telephone line jack at the bottom of the telephone base Then plug the other end of the cord into the wall telephone outlet www vtechphones com Installation Check battery indicator When the handset displays WARNING CHECK BATTERY, it indicates one of the following: 1 There is no battery in your handset You need to install the supplied battery into your handset (see Install handset battery on page 5) 2 The battery needs to be replaced 3 The battery has been installed incorrectly Please reinstall (see Install handset battery) and/or see the diagram in the battery compartment of the handset Check for dial tone After the battery is charged, press or SPEAKER on the handset You should hear a dial tone If not, see the Troubleshooting section near the end of this user’s manual CAUTION: Use only the VTech power supply provided with your telephone Getting started www vtechphones com 7 • If the phone will not be used for a long period of time, remove the battery pack to prevent possible leakage • If you have any trouble installing your phone, please refer to the Troubleshooting section near the end of this manual • When in LOW BATTERY mode, the keypad sounds, backlighting and speakerphone features will not work When the battery has been charged, these features will return to their normal function Installation If you subscribe to DSL service If you hear interference during conversations, and/or your caller ID features are not functioning properly, and you subscribe to DSL service from your telephone company, install a noise filter to the telephone line between the base unit and the telephone line jack Contact your DSL provider to obtain a noise filter. T el ephone line cord (RJ11C) Noise filter (For DSL users) To single telephone jack Belt clip (optional) To attach To remove www vtechphones com Getting started Wall mounting (optional) The wall mount brackets are designed for use on standard wall mount plates only. 1. Plug the connector of the base power adaptor to the connector jack at the bottom of the base unit. Then plug the adaptor into an electrical outlet. 2. Connect the telephone line cord to the jack at the bottom of the base unit, and the other end to the wall jack. 3. Line up the tabs on the wall mount adaptors with the holes at the bottom of the base unit/back of the charger. Snap the wall mount bracket firmly in place. 4. Moun...