Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
5 Guests may leave the conference call by pressing their call control button. When they do you will hear a single tone in the master headset as each guest leaves the call. To see how many headsets are subscribed to the base, refer to the lower left corner of the PerSono Suite software screen. The first headset is the master headset and the number inside the next headset is the number of guest headsets subscribed to the base. The examples below show 1, then 2, then 3, guest headsets subscribed to the base in addition to the master headset. Muting the Headset You can mute/unmute the headset the following ways: Headset Base PerSono Suite Software* Press the volume down button (at least 1. seconds) until the base talk button indicator light for the active call becomes solid red. Short press (less than one second) of a red desk phone or PC talk button on the base will unmute the headset. You cannot mute the headset using the desk phone or PC talk buttons. Click the green headset icon. The headset icon will turn red indicating the headset transmit is muted. Clicking the headset icon again will unmute the headset. * Desk phone and PC audio links have to be brought up by the headset or base. You cannot initiate an audio link via the Audio Control Screen in the PerSono Suite software. Subscribing a Master Headset The headset and base are subscribed to each other at the factory. In the event that you need to subscribe a new master headset to the base you can do so one of two ways. You can subscribe a master headset to the base with the headset docked (secure subscription) or undocked (over-the-air subscription). In either case, the system must be idle (not on a call). Headset Docked Headset Undocked Double press the subscription button on the base. The subscription light will flash red and green. When the subscription light becomes solid green, the headset and based are subscribed to one another. Double press the subscription button on the base. The subscription light will flash red and green. Press the volume up button on the headset for three seconds until the headset indicator light turns solid green. When the subscription light on the base becomes solid green, the headset and base are subscribed to one another. Note If the subscription process times out after two minutes or if the subscription process fails, the subscription light will become solid red for four seconds and then return to its previous state. If this occurs, try to re-subscribe the headset again. 1 2 3 Setting Default Line to Desk Phone or PC The Savi Office system ships with the desk phone as the default outbound line. This means any call initiated from the headset with the call control button will open desk phone audio. You can change your default outbound line from the base talk buttons. While the system is in idle mode, press and hold the PC talk button or the desk phone talk button for three seconds to select that device as your default outbound line. The talk button indicator light will flash green for four seconds confirming the new setting. Subscription Button Indicator Light Master headset subscribed to base Solid green Base in master subscribing mode Flashes red and green Base conferencing in additional guest headset(s) Flashes yellow and green Active conference call with guest headsets subscribed to base Solid yellow Desk Phone Talk Button PC Talk Button Indicator Light Indicator Light Desk Phone and PC Talk Buttons Indicator Lights Toggling On/Off Over-the-Air Subscription The Savi Office system ships with the over-the-air subscription enabled. You can toggle on or off over-the-air subscription using the subscription button on the base. With the master headset undocked and the system idle, press the subscription button for three seconds. The subscription button will flash green for four seconds if over-the-air subscription is on and red for four seconds if off. Setting the Range With the master headset docked and the system idle, press the subscription button for three seconds. Both the desk phone and the PC talk buttons will flash green for high range. If you press the subscription button again for three seconds, the talk buttons will flash yellow for medium range. If you press the subscription button again for three seconds, the talk buttons will flash red for low range. Ending Subscription If the base is in subscription mode (secure or over-the-air), and you want to end the base from searching for a headset, press the subscription button again. The subscription light will turn solid red for four seconds and then go to it’s previous state. Placing the Headset in Sleep Mode If you won’t be using the headset for a long duration and the headset will not be in the charge cradle, you can put the headset in sleep mode by pressing the call control button for three seconds while in an idle state. To exit sleep mode, press the headset call control button again for three seconds. No active audio link Off Incoming call Flashes green Active audio...