Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Quickstart Guide NOTE: YOU MUST INSTALL INCLUDED SOFTWARE BEFORE ATTACHING YOUR PHOTO ALBUM TO YOUR PC. Software Installation: 1. Insert the included CD into your PC’s CDROM drive 2. Open “My Computer” and find the CD you just inserted. It will appear similar to the image below: My Comp Screen.jpg 3. Double click the CD drive icon to open the CD. ** NOTE** THE ACTUAL DRIVE LETTER (D IN THIS CASE) COULD BE DIFFERENT ON YOUR PC. LOOK FOR THE DRIVE THAT IS THE CDROM ON YOUR PARTICULAR PC 4. Double click the “Digital Photo Frame Tool folder icon. Inside that folder, double click the “PhotoViewer vX.XX Setup ( without bios).exe” icon. NOTE: THE EXACT REVISION NUMBER OF THE VERSION ON YOUR CD COULD BE DIFFERENT THAN IN THE PHOTO BELOW: App Screen.jpg 5. After double clicking this icon, the following screen should appear: screen1.jpg 6. Follow the on-screen prompts to install the software. Accept all the “defaults” that the program suggests (if you are experienced in installing software you can customize your install) You are now ready to charge your Keychain Photo Album. 1. Using the included plug the cable into your PC first, and then into your Mini Photo Album. NOTE: YOUR PHOTO ALBUM MUST BE FULLY CHARGED BEFORE USING IT. THIS CHARGING TIME IS TYPICALLY 2-3 HOURS 2. When the unit if first plugged in to your PC, the following screen appears: There will be blinking battery icon in the lower left hand corner. This icon will stop flashing once your unit is fully charged 3. Once the unit is fully charged, unplug it from your PC and turn it off using the ON/ OFF switch on the side of the unit. 4. With the unit off, plug it back into your PC (using the same procedure as #1). 5. You will see the following screen: Using the DOWN navigation button on the side of the unit, move the cursor down to the USB Update position: Then press the MENU (top) button to select the Update mode. The following screen will appear: You are now ready to transfer images to and from your unit. 6. Once the unit is in the “updating” mode, go to your START/ALL PROGRAMS menu and look for the newly installed program group. It should be called “Photo Viewer” 7. Go to this new program group and double click the Photoviewer icon to open the program 8. Once open, you should see a program screen similar to the one below: xfer1.jpg 9. To add pictures to your Mini Photo Album from your PC, navigate to the image on your PC using the controls on the left-hand side of the Photoviewer software 10. Select the photo you want to add by clicking on it once. 11. Then click the blue arrow (circled on the image as “1”) to POST the image to the keychain. 12. Then to finalize the transfer, click the SYNCHRONIZE button (circled on the image as “2”) to make the transfer complete 13. You can delete images on the Photo Key-Chain by selecting them, pressing the DELETE button and then the synchronize button Once you have completed the transfer of images to your Keychain Photo Album, exit the Photoviewer software and remove your unit from your PC by disconnecting the USB cable from your Photo Album first and then from your PC. To turn on the Photo Album, press the MENU button for 2 seconds. To flip through images stored on your Photo Album, use the UP / DOWN buttons. Detailed Instructions: Supported graphic formats • BMP • JPG • GIF Button Functions 1. Reset 2. UP 3. MENU 4. DOWN NOTE: If the unit stops functioning properly, press the reset button for 2sec, then turn the unit back on This side shows navigation images on PC This side shows images installed on Mini Photo Album 1 2 Menu Functions: Power OFF – This menu selection will turn the unit off. Using the up/down buttons. Press the MENU button to make selections DELETE IMAGE - This selection will allow you to manually delete an image while viewing it. While in the viewer mode, select MENU, and scroll down to DELETE. Press MENU again. You will get a confirmation screen “DELETE ?”. Press MENU again delete the image. DISPLAY MODE - This selection allows you to choose an AUTO or MANUAL slide show. Selecting AUTO will generate an automatic slide show. You can adjust the timing of each slide by using the up/down buttons. Selecting MANUAL will allow you to manually select images using the up/down buttons. Press MENU to exit and return to the main menu CLOCK SET – This selection will allow you to set the unit’s clock. Use the MENU button to select the date/time/day line, and the use the buttons to select the correct date/time/day. Press MENU to exit this function CLOCK DISP - This selection displays the date / time on the screen Auto ON/OFF - Selecting “ ON” will put the unit into an auto power- off mode and if no buttons are pushed the unit will shut off after a predetermined amount of time. This function saves battery power Selecting OFF turns this feature off and returns to the main menu. EXIT - This selection exits the menu screen and returns to the image or clock display Specifications: • Image storage capacity ~ 60 images ...