Votos - 4, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Select Start in the Network Settings screen, and then press the E button. The Network Status screen appears. The product attempts to verify the network connection and fails. Network Settings Wired network connection failed. MAC Address XX:XX:XX:XX:XX:XX IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Gateway 0.0.0.0 DNS Server 0.0.0.0 Unable to connect to the network. Try the following: check if your IP address is set correctly in IP Settings. Contact your Internet service provider for more information. Retry IP Settings Previous OK 2 . Select IP Settings on the right of the screen, and then press E button. The IP Settings screen appears. 3 . Select the IP Mode field, and then set it to Manual. 4 . Use the number keypad on your remote to enter the Network values. Use the ^Ў<> buttons on the remote to move from entry field to entry field. | NOTE | You can get these values from your Internet provider. You can also view these values on most Windows computers. For instructions, see "Getting the Network Settings Values." on this page. 5 . When done, highlight OK, and then press E button. The product verifies the network connection and then connects to the network. < Getting the Network Settings Values > You can view your Network Settings values on most Windows computers. To view the Network Settings values, follow these steps: • Windows XP 1 . Right click the Network icon on the bottom right of the Windows desktop. 2 . In the pop-up menu, click Status. 3 . On the dialog that appears, click the Support tab. 4 . On the Support tab, click the Details button. 5 . The Network settings are displayed. • Windows 7 1 . Click the Network icon on the bottom right of the Windows desktop. 2 . In the pop-up menu, click Network and Sharing Centre. 3 . On the dialog that appears, click the Local Area Connection or Wireless Network Connection depending on your network connection. 4 . On the Support tab, click the Details button. The Network settings are displayed. | NOTE | Depending on your Windows version, the information may differ. Wireless Network You can setup a wireless network connection in three ways: - Wireless Automatic - Wireless Manual - WPS(PBC) When you configure the wireless network connection, any wireless network devices currently connected through the product or, if applicable, the product's current wired connection, will be disconnected. ............................................................................................................ ............................................................................................ | 34 English Settings Wireless (General) - Automatic After following Steps 1 to 3 in "Configuring Your Network Connection" on page 32. 1 . Select Start in the Network Settings screen, and then press the E button. The product searches for and then displays a list of the available networks. Network Settings Refresh WPS(PBC) Previous Next Cancel Select your wireless router from the list. 1/10 ELT JSY KT_WLAN_C361 Mirhenge_edu SO070VOIP iptime23 2 . Select the desired network, and then press the E button. 3 . Select Next, and then press the E button again. 4 . On the Security screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with an arrow button, and then pressing E button. 5 . When done, select Next at the right of the screen. The product verifies the network connection and then connects to the network. | NOTE | You should be able to find the Security Code or Pass Phrase on one of the set up screens you used to set up your router or modem. Wireless (General) - Manual If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually. After folloiwng Steps 1 to 3 in "Configuring Your Network Connection" on page 32. 1 . Select Start in the Network Settings screen, and then press the E button. The product searches for and then displays a list of the available networks. 2 . Select the desired network or the Add Network, and then press the E button. 3 . Select Next, and then press the E button again. 4 . If you select the Add Network, enter your wireless router's name to connect. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with the ^Ў<> buttons, and then pressing the E button. Select Next, and then press the E button again. You can select security type, and then select Next, and then press the E button again. 5 . On the Security screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with the ^Ў<> buttons, and then pressing the E button. 6 . When done, select Next at the right of the screen, and then press the E button. 7 . The Network Status screen appears. The product attempts to verify the network connection and fails. 8 . Select IP Settin...
Otros modelos de este manual:Blu-Ray - HT-E6730W (8.94 mb)
Blu-Ray - HT-E6750W (8.94 mb)