Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Leave the drive for about 1 hour before using. Keep magnetic objects away from the drive. Do not insert any foreign metal object inside the drive. Do not touch the lens. If noise is heard from radio or TV, move the drive 2 m (about 6 ft.) away from the radio or TV. I Do not use any other USB cable with the drive, except the supplied USB cable. 10 Precautions AC Adaptor Do not plug-in or remove the AC adaptor using wet hands. 0 Make sure the AC outlet or cord for the AC adaptor does not exceed the limit of their electrical ratings. Make sure the prongs of AC adaptor are fully inserted into the AC outlet. Periodically remove the dust from the prongs of AC adaptor. Only use the AC adaptor indoors. Do not damage the AC adaptor by scratching or modifying, or bending its prongs. 0 Do not use the AC adaptor under the following conditions. —when it is damaged —when there is smoke or strange smell —when an abnormal sound is heard Use only the supplied AC adaptor (№ P. 21) Do not disassemble the AC adaptor. Do not scratch, smudge, write or label both surfaces of Disc. Do not leave the Disc in direct sunlight, near a heat source or especially in a hot automobile. Do not use chemicals or cleanser to clean Disc. Do not wipe Disc with dried hard cloth. Do not touch the data side (the side without the label) of Disc. Avoid finger prints and scratches while holding it. Do not throw or bend Disc. Accessories Make sure that the following accessories are included with the drive. If anything is missing, contact your dealer immediately. □ AC Adaptor The Model No. of AC adaptor is written on the bottom of the drive. □ Operating Instructions (this manual) v_ □ Setup Disk [Before opening the packet, please read the End-User License Agreement.] □ Writing Software [B’s Recorder GOLD and B's CUP] 12 Part Names ■ Front/Right Side view Note: Part Names ■ Rear /Bottom view MODE Switch Setting Before setting the MODE switch, make sure that the drive is OFF. MODE switch allows you to set “POWER MODE” below). Set the switch No.1 to ON or OFF using a pointed object like a pen. Note: • Make sure that you use the drive with MODE switch No.2 set to OFF. Setting the Power Mode The factory setting is set to “OFF”. MODE Switch Setting Description 1 ON No need to connect with your computer, the drive can be automatically turned on when the power is supplied from the AC adaptor. OFF The power of the drive is automatically turned on/off when your computer is turned on/off. System Requirements Unit*1 • IBM PC/AT compatible Computer CPU •Pentium® D 233 MHz or Better Virtual memory • 32 MB or more (64 MB is recommended.) Free disk space • 100 MB or more (800 MB is recommended.) • Windows 98*z Operating System • Windows 2000*3 • Windows Me*4 *’ It must have an USB port. *2 Microsoft® Windows® 98 operating system (hereafter Windows 98) *3 Microsoft® Windows® 2000 operating system (hereafter Windows 2000) *4 Microsoft® Windows® Millennium Edition operating system (hereafter Windows Me) 16 Setup Your Computer Confirmation of Windows version Right-click the “My Computer” icon, then click “Properties”. The “System Properties" window appears. Confirm at the System windows that there is “Microsoft Windows 98", “Microsoft Windows 2000” or “Microsoft Windows Me” is installed. ' I General |j Device Manager | Hardware Profiles ] Performance | System: Microsoft Windows Me 4.90.3000 Registered to; Note: • This drive is not compatible with Windows 95 and Windows NT. If you wish to upgrade the Operation System from Windows 95 to Windows 98, you will need the latest USB driver. You should check with your PC manufacturer’s support center or check their website for the latest USB driver. Setup Your Computer Installing the device driver Caution: • Please use your computer with AC power to prevent the battery of your computer from running down while installing drive. 1. Insert the supplied Setup disk into your computer’s floppy disk drive. 2. Double-click the “My computer” icon on the screen and then double-click “A:” (depending on floppy disk drive letter). 3. Double-click “Setup.exe”. The “Setup” window appears. I* This pfqjram wil setup tot your Portable CD-R/RW Diive(KXL-RW21A) Check the items you want, arid then click OK i7 Install I |7 Qevice driver , [7 £(efci fie Derivation Folder fof Help fie |C: ^Program Fiei\cdrrt*G6 gtowie | / f* yninslafl D evice driver and Help file 18 Setup Your Computer 4. Click “Device driver” and then click iOK Start installing and when it finishes next window appears like below. Note: • You can install the Help File, if you click on “Help file”. EETOE v 1*1 Qjp Install successfully completed Click OK. and then remove the Setup Disk from Floppy Disk Drive. [.........~0K 5. Click |OK and then remove the Setup disk. 6. Connect the drive to your computer. Follow steps ©to(4) at “Connection”. («3- p. 21) “CDRRW06 USB CD-R/RW device ...