Votos - 3, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
However, if the buffer becomes empty temporarily, this may cause errors in recording data. What is Auto-Run? If inserting a CD into a drive, the operating system executes the Autorun.inf file of the CD automatically. What is Justlink? This function is to check the buffer to see if there are data while recording. If the buffer is empty, it waits at the address and then restarts recording after the buffer is full. You can avoid Buffer Under-Run problems by applying the above-mentioned principle. Troubleshooting Recommended Disc Types CD-R MCC, RITEK, CMC, SKC, BEALL, PRODISK, MAXELL, ACER, MPO, FUJI, TAIYO YUDEN, TDK, GIGA, PLASMON CD-RW CD-RW : RICOH , RITEK , MCC , PRODISK , SKC , CMC, ACER (1X - 4X) H/S-RW : RICOH , CMC , RITEK , ACER , PRODISK , SKC (10X) U/S RW : MCC , RITEK (24X, 32X) General DMA Installation Guide Windows 98/Me Important! Please read the entire DMA installation guide before installing your CD-R/RW drive. About DMA Installation For stable writing performance at high speeds, Installation of DMA transfer mode for E-IDE/ATAPI interface is strongly recommended. We recommend DMA mode for fast writing. DMA SettingBefore you install your CD-R/RW drive, we recommend to set DMA to enabled on your PC system. See the following procedure to set DMA transfer mode in windows oprerating system. (Windows 98/ME) + Click on START + Click on Settings + Select Control Panel + Select the System Icon + Select the Device Manager panel in System Properties + Expand the CD-ROM icon + Select your CD-R/RW drive + Click on the Properties button + Click on the Settings tab + Check the DMA checkbox to enables DMA. + Click OK + Restart your PC Windows 2000/XPSelect the DMA mode by selecting [Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel Advanced Information] Troubleshooting Problem Meaning / Solution The CD-R/RW drive is notdetected by the computer. After installing the CD-R/RW drive, the PC gets slower. The CD-R/RW drive is notrecognized by MS-DOS. The CD-R/RW drive is notdetected by Windows. No sound is heard from an audio CD. A CD is not read or is read too slowly. The disc compartment will not open. When the MPEG software plays a Video CD, the picturesare not regular and the runningspeed is too slow. The Disc is not in message is displayed even though a dischas been inserted. The CD-R/RW drive is notdetected after it is connected to a sound card. IN CD has the Formatted Disc Eject function. When recording NERO or EasyCD Creator, it will be recorded not on a CD but a form of image file. The Recorder cannot recognize the disc. Check that the power, audio and IDE cables are correctly connected to the computer. Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the CD-R/RW drive in master mode. Check the position of the jumper in the master/slave select terminal. Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. -Http://samsung-ODD.com -Http://samsung.com This case may occur when there is a Windows installation problem; reinstall Windows. Check whether the audio cable is correctly connected to the sound output terminal on the CD-R/RW drive and the sound card CD-IN terminal. Check that the sound card is operational. Adjust the volume control. Run the CD player supplied with Windows or your sound card. You can listen to the CD by connecting headphones to the appropriate connector. If you have installed the appropriate player, such as Microsoft Windows Media Player, you can adjust the volume using the headphone volume control on the drive front panel. Check whether the CD is of good quality and clean it, if necessary. Check that the power cable is correctly connected. Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. Adjust the size of the replay screen. After checking the display resolution, adjust it, if necessary. The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. Clean the disc and try again. The interface mode of the sound card is AT-BUS. You must therefore connect the CD-R/RW drive to the IDE port on the PC mother board, rather than to the sound card, or install an E- IDE compatible sound card. Right-click the mouse on TRAY ICON (right side of the menu bar at the bottom of the monitor) and then select "Eject" to take the CD out. Select the drive where the disc is inserted from Windows Explorer. Right-click the mouse and select "Eject" to take the CD out. This seems to occur when you select the recording function as the system selects "Image Recorder" instead of SW-252. In this case, select a recorder from the menu items at the upper part of NERO or Easy CD Creator and then select SW-252 from the Recorder Selection window. When installing the recording so...