Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Installing the DVD-ROM Drive 1 Make sure that the PC is powered off and disconnected from any power source. 2 If necessary, attach a horizontal bracket to both sides of the drive. 3 Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the illustration. Item Description Computer Intel Pentium III (or higher), 350MHz or higher, 128 MB of RAM (or higher) with an IDE interface Disk space 100 MB minimum Windows version Windows 95 OSR2 / 98 / 2000 / ME / XP /Windows NT 4.0 (or higher) DVD-ROM DRIVE SD-616 User's Guide BG68-00342A Rev.03 Safety Precautions The following diagrams illustrate the precautions to be taken when using your DVD-ROM drive. You must not use the drive in any manner other than that specified in this guide. Avoid exposing your eyes or skin to direct or scattered radiation. CAUTION Do not attempt to repair the DVD-ROM drive yourself. Contact your dealer or local SAMSUNG representative for all repairs. If you make any adjustments or perform any operations other than those specified in this guide, you run the risk of exposure to hazardous radiation. WARRANTY Please refer to the Samsung limited warranty statements. Precautions 1. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. 2. Always check each disc for cracks before using it. If there are cracks on the surfaces, especially around the border of the center hole, we recommend that you make a copy of the disc immediately and then stop using it. If you continue using the disc, it will probably develop more cracks and eventually cause irreparable damage. 3. Do not use poor quality discs: From unknown sources Without any copyright Scratched or damaged in any way 6 7 Setting Up the Device Driver Installing the Device Driver Using the DVD-ROM Drive Storing and Cleaning Your Discs Solving Technical Problems Automatic Setup Manual Setup LAST DRIVE = Z - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C :\SAMSUNG\MSCDEX /D:SSCD000 SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. Technical Specifications 1. Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features 2. Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details) 3. Master/slave select terminal 4. 40-pin host IDE interface connector 5. 4-pin power terminal The product firmware can be upgraded by downloading the updated file from the following Web site: Use of the brackets depends on your computer model; you can purchase these accessories separately from your computer dealer. If you have no free expansion slot, install the drive in place of the diskette drive. DVD-ROM drive 1. Power cable 2. Master/slave select terminal 3. IDE cable 4. Audio cable 1 Connecting the power cable The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the DVD-ROM drive. 2 Installing a jumper on the master/slave select terminal Install the jumper in the correct position on the terminal: MA to use the device in the master mode SL to use the device in the slave mode CS to control the device via a CSEL host interface signal See Step 3 for further details. 3 Connecting the IDE cable Two configurations are possible. The DVD-ROM drive is the only IDE device in addition to the hard disk. 4 Connecting the audio cable from a sound card Connect the 4-pin audio cable between the sound output terminal on the DVDROM drive and the audio input terminal on the sound card. Install the jumper in the SL position (Slave). Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to the DVD-ROM drive and then to the hard disk. Install the jumper in the MA position (Master). Connect the 40-pin flat IDE cable from a second IDE port on the mother board directly to the DVD-ROM drive or first to another additional IDE drive and then to the DVD-ROM drive. IDE port Mother board DVD-ROM (SL) Hard disk (MA) You already have an additional IDE device installed in your computer. Mother board Second IDE cable DVD-ROM (MA) CD-ROM (SL) Hard disk (SL) Hard disk (MA) First IDE cable 1 Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive. To do so, type A: after the C:\ prompt and press [Enter]. 2 Type CDSETUP and press [Enter]. 3 Reboot the computer. 1 Make the C:\SAMSUNG directory. 2 Copy the files from the diskette to the C:\SAMSUNG directory. To do so, type COPY A:*.* C:\SAMSUN...