Votos - 2, Puntuación media: 4 ( )

Fabricar: LG Tamaño del archivo: 170.18 kb Nombre del archivo: Idioma del manual:

But, most High Definition TVs and multimedia monitors do support HDCP. Refer to the PC or graphic card maker’s web site to see if your card supports HDCP. Some video cards that currently support HDCP: -nVIDIA: GeForce 7800 GTX 512 / 7900 GT / 7900 GX2 / 7900 GTX / 7950 GX2 / 8600 GS / 8600 GT / 8600 GTS / 8800 GTX or higher with 256MB min memory. - ATI: Radeon® X1950/ HD2300/ HD2400/ HD2600 series or higher with 256MB min memory. *When using ATI RadeonTM HD 1000 Series Graphic Card, some BLURAY movie title can not be played on Windows7 normally. It caused by giving up supporting the device driver of this Graphic Card by ATI RadeonTM. For more information, Please contact to customer service center or website of ATI RadeonTM. *1 Graphic card driver shall meet AACS compliance criteria. Please consult your graphics card vendor for proper driver solution. *2 HDCP (High Bandwidth Digital Content Protection): Required to view pre-recoded Blu-ray Disc which is copy protected. 3 . Occasionally CD-R and CD-RW discs written by a CD-R/RW drive cannot be read by other CD drives. These unreadable discs may need to be read using the CD-R/RW drive they were created with. The disc written using the CD-R/RW drive might not be readable by CD-ROMs other than Multi-read compatible (UDF compatible) CD-ROMs. Multiread compatible (UDF compatible) CD-ROMs are CD-ROMs that can read low reflectance and support Packet Write. . Please note: Certain software (i.e. particularly those including Video playback) may require a considerably increased specification PC to give acceptable results. While this Blu-ray Disc Rewriter can read DVD-video or BD-MV(BD-ROM) discs, decoding them to display on your pc’s monitor requires separate MPEG, H.264 or VC-1 decoding that is done by separate hardware (either an MPEG, H.264 or VC-1 decoder card or MPEG, H.264 or VC-1 decoding done by your video card), or separate software that you install to do MPEG, H.264 or VC-1 decoding. For further details, refer to the documentation that comes with MPEG, H.264 or VC-1 software. Location and Function of Controls Front Panel Rear Panel 1 234 1 2 1. Disc Tray 1. SATA Power Connector (15 pin) 2. Drive activity indicator 2. SATA Data Connector (7 pin) The LED is used to indicate the operation of Blu-ray Disc Rewriter. 3. Emergency Eject Hole 4. Eject Button 4 Installing the Drive Before installing the drive, please note the following points. ¦ You will need the following: • A screw driver of a suitable size to fit the securing screws for the drive unit. • The manual for the computer, so you can find the mounting positions for the SATA cable. ¦ Turn off all peripheral appliances of the computer and the computer itself, and disconnect their power cords from the wall sockets. ¦ Discharge any static electricity on your person by touching the computer covers, etc. Removing the Computer Cover Make sure all peripheral devices of the computer and the computer itself are turned off, and then remove the cover. Refer to the manual for the computer for details about removing the cover. NOTE : There may be sharp edges inside the computer so take care to avoid injury. Mounting the Drive 1. Remove the a 51/4. drive bay panel from the computer. Refer to the manual for the computer for details. 2. Insert the drive unit into the bay. Do not apply excessive pressure to the cables inside the computer. 3. Secure the drive with the screws. If there is not much space behind the drive, connect the SATA and other cables before securing the drive. NOTE : This is a general installation guide. If your PC hardware appears different, please consult your hardware manual for installing peripheral devices. 5 PC Connection The Blu-ray Disc Rewriter connects to the motherboard of the host computer using a SATA interface cable. Data cable Power cable Data cable Power cable Red Connecting the SATA Power Cable Connect the power cable so the projection of the cable connector side to come to the left side. Be careful not to connect upside down. NOTE : Improper connection may damage the drive and void the warranty. Generally, the power connector can only fit one way. Connect to the power connector of the PC. Connecting the SATA Data Cable Connect the data cable. Be careful not to connect upside down. 6 Connect to the SATA connector on the PC's Motherboard. Device Drivers When using Windows XP SP2, Vista and Windows 7, no special device driver is required. Your system, upon Power On and bootup after installing and connecting the new Blu-ray Disc Rewriter will recognize and load native software drivers automatically. For Windows XP Users ¦ In order to ensure normal drive operation, please check the following: • The drive is displayed in Windows XP : [Control Panel]-([Performance and Maintenance])-[System][ Hardware]-[Device Manager]-[DVD/CD-ROM-drives] ¦ If the drive is not recognized by your computer, please check the following items. • If an indicator is displayed on the IDE ATA/ATAPI controllers in [Contro...

Descargar ahora

Introduzca dos números de la imagen: