Votos - 2, Puntuación media: 4.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Remove the 51/4. drive bay panel from the computer. Refer to the manual for the computer for details. 2. Insert the drive unit into the bay. Do not apply excessive pressure to the cables inside the computer. 3. Secure the drive with the screws. If there is not enough space behind the drive, connect the IDE and other cables before securing the drive. NOTE : This is a general installation guide. If your PC hardware appears different, please consult your hardware manual for installing peripheral devices. Jumper Setup Before installation, set the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive. R E A D W RI T E R E A D W R IT E 4 NOTE : If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run or may malfunction. Careful attention is necessary. MA: Master SL: Slave CS: Cable Select (CSEL) NOTE : Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. If you use CSEL setting, the MASTER/SLAVE setting will be made automatically, depending on the hardware configuration. For more details refer to the manual of your computer. PC Connection The Super Multi DVD Rewriter connects to the motherboard of the host computer using an IDE interface cable. You may connect the Super Multi DVD Rewriter as a Slave or Master device, depending on your computer. To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. NOTE : A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and Super Multi DVD Rewriters are then set differently. 5 Name Function Drive set as Master Drive set as Slave MA (Master) SL (Slave) CS (Cable Select) C S S L M A Drive mode set by CSEL on the host IDE interface Primary connector Secondary connector Master drive (Super Multi DVD Rewriter) (Jumper left as Master) Motherboard - OR - DIGITAL ANALOG INTERFACEPOWER DRCSM SLA GLG39 1 +5 +12GND 40 2 AUDIOAUDIO Master drive (Booting hard disk) Secondary connector Master drive (Super Multi DVD Rewriter) (Jumper left as Master) Slave drive (Other IDE drive) DIGITALANALOG INTERFACEPOWER DRCSM SLA GLG 39 1 +5+12GND 40 2 AUDIO AUDIO DIGITALANALOG INTERFACEPOWER DRCSM SLA GLG 39 1 +5+12GND 40 2 AUDIO AUDIO Master drive (Booting hard disk) Primary connector To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel to SL. Connecting the Power Connector Connect the power cable from the computer’s power supply to the socket on the drive unit, fitting the connector firmly into the power in connector. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type. Connecting the Interface Connector Connect the 80-pin IDE cable to the back of the Super Multi DVD Rewriter, making sure the coloured (red) stripe on the IDE cable is connected to pin 1 on the Super Multi DVD Rewriter (Pin 1 is closest to the Power Connector). 6 Slave drive (Super Multi DVD Rewriter) (Jumper set to Slave) Master drive (Booting hard disk) - OR - DIGITALANALOG INTERFACEPOWER DRCSM SLA GLG 39 1 +5+12GND 40 2 AUDIO AUDIO Secondary connector Master drive (Other IDE drive) Slave drive (Super Multi DVD Rewriter) (Jumper set to Slave) DIGITALANALOG INTERFACEPOWER D RCSM SL A GLG 39 1 +5+12GND 40 2 AUDIOAUDIO DIGITAL ANALOG INTERFACEPOWER D RCSM SL A GLG 39 1 +5+12 GND 40 2 AUDIOAUDIO Master drive (Booting hard disk) Primary connector Beveled edge up NOTE : Improper connection may damage the drive and void the warranty. Generally, the power connector can only fit one way. Pin1 Red-edge NOTE : Generally, the IDE connector is keyed and will only fit one way. Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. Device Drivers When using Windows 2000 Professional/XP Home Edition/XP Professional/ Vista/ Windows 7, no special device driver is required. Your system, upon Power On and bootup after installing and connecting the new Super Multi DVD Rewriter, will recognize and load native software drivers automatically. Please consult the following internet sites: (then choose your country from the list) For Windows 2000/XP/Vista Users ¦ In order to ensure normal drive operation, please check the following: • The drive is displayed in Windows 2000/XP : [Control Panel]-[System]-[Hardware]-[Device Manager][ DVD/CD-ROM-drives] Windows Vista : [Control Panel]-[Devi...