Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Do not use it in tilted position. • Don’t move the drive suddenly from a cold place to a warm one or raise the room temperature suddenly. Condensation may occur, causing abnormal operation. • Make sure to remove the disc before moving the drive. The disc may become damaged, causing data loss. • Be careful to prevent foreign objects, such as liquids or metal, from entering the drive. In case a foreign object enters the drive, please consult the dealer where the drive was purchased. • Don’t interrupt the electric power while the drive is operating. • When connecting two IDE devices to the Primary or Secondary connectors, make sure that the two devices are not configured as both Master, or both Slave. If they are both set the same, Windows may fail to run or recognize the drives. • The total length of the IDE cable should be no more than 18 inches (about 45 cm). 1 Features • Enhanced-IDE (ATAPI) interface. • Power tray loading and ejection of disc. (The disc can also be ejected manually.) • Combination CD-R/RW, DVD-R/RW, DVD-R DL, DVD+R/RW, DVD+R DL, DVD-RAM Drive functions into one drive. • Supports Region playback control Phase II. • Supports SecurDiscTM Technology. • Automatic buffer underrun error prevention technology. System Environment Computer This unit can be operated in the system environment explained here. System requirements CPU: Pentium III 1.0GHz (Recommended system requirements for optimal performance, CPU: Pentium IV 2.4GHz or faster, Memory: 512MB or greater). VGA Card Memory 128MB or greater. Hard disk 20GB or more free space. (The free space needed for writing depends on the quantity of data.) Interface Enhanced-IDE interface (as Primary Slave, Secondary Master or Slave) Drive bay 5.25-inch half-height bay required Power +5V/+12V power socket required Software Required OS Windows 2000 Professional/XP(Home Edition/ Professional)/Vista, Direct X 9.0 or Higher is required CD-R, CD-RW, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD±R DL, DVD-RAM media CD-R : LG, Mitsubishi Kagaku Media, Verbatim, That’s, TDK, Ritek or HP discs are recommended. CD-RW : LG, Mitsubishi Kagaku Media, Verbatim are recommended. DVD-R : Mitsubishi Kagaku Media, Maxell, That’s are recommended. DVD-RW : Victor. JVC, Mitsubishi Kagaku Media, TDK are recommended. DVD+R : Mitsubishi Kagaku Media, That’s, Maxell are recommended. DVD+RW : TDK, Mitsubishi Kagaku Media, Ricoh are recommended. DVD±R DL : Mitsubishi Kagaku Media, Verbatim are recommended. DVD-RAM : Maxell, Mitsubishi Kagaku Media are recommended. * Compatibility problem in write/read function may occur with media depending on the media manufacturing quality. * For DVD±R 20x support media: Mitsubishi Kagaku Media, Taiyo Yuden are recommended. * For Optimal 18x, 20x writing, 80 pin E-IDE cable and Pentium IV 2.4GHz or faster are recommended. * Upon the media condition or some of user’s environment the maximum speed sometimes could not be guaranteed. 2 . Occasionally CD-R and CD-RW discs written by a CD-R/RW drive cannot be read by other CD drives*. These unreadable discs may need to be read using the CD-R/RW drive they were created with * The disc written using the CD-R/RW drive might not be readable by CD-ROMs other than Multi-read compatible (UDF compatible) CD-ROMs Multiread compatible (UDF compatible) CD-ROMs are: 1. CD-ROMs that can read low reflectance. 2. CD-ROMs that support Packet Write. . Please note: Certain software (i.e. particularly those including Video playback) may require a considerably increased specification PC to give acceptable results. While this Super Multi DVD Rewriter can read DVD-video discs, decoding them to display on your pc’s monitor requires separate MPEG decoding that is done by separate hardware (either an MPEG decoder card or MPEG decoding done by your video card), or separate software that you install to do MPEG decoding. For further details, refer to the documentation that comes with MPEG software. Location and Function of Controls Front Panel Rear Panel 1 23 4 1. Disc Tray 2. Emergency Eject Hole 3. Stop/Eject Button 4. Drive activity indicators The LED used to indicate the operation of Super Multi DVD Rewriter. 1 2 3 This connector is not supported. 1. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 2. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) Interface using a 80-pin flat IDE cable. NOTE : Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting this cable. 3. Power Connector 3 Installing the Drive Before installing the drive, please note the following points. ¦ You will need the following: • A screw driver of a suitable size to fit the securing screws for the drive unit. • The manual for the computer, so you can find the mounting positions for the IDE controller cab...