Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
3.) SHUFF (Shuffle) Indicator – Appears when Random playback mode is selected. 4.) INTRO Indicator – Appears when Intro playback mode is selected. 5.) HOLD Indicator – Appears when HOLD switch is set to ‘On’position. 6.) (Repeat 1) /ALL Indicators – Appears when the Repeat playback mode is selected. 7.) Battery Status Indicator – Appears when battery level becomes low. 8.) Elapsed Time (Seconds) Display. 9.) Elapsed Time (Minutes) Display. 10.) ANTI-SHOCK Indicator – Indicates ESP Protection is activated. 8 HD8100R_031604.p65 8 16/3/2004, 14:18 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS SPECIAL FUNCTIONS HOLD Switch The HOLD switch on the bottom of the cabinet must be in the ‘Off’ (left) position to start the CD player. If you plan to carry the CD player in a handbag, briefcase, school bag, back pack, etc, slide the HOLD switch to the ‘On’ (right) position. While the HOLD switch is ‘On’ all of the controls on the CD door are disabled. This prevents the player from starting accidentally by something pressing against the PLAY/PAUSE button. HOLD(Off) After you begin CD playback you may also slide the HOLD switch to the ‘On’ (right) position to disable all the controls on the CD door. You can then place the player in a handbag, backpack, etc, and do not have to worry that the player will be accidentally turned off by something pressing against the STOP button or Track Skip buttons. BASS BOOST ON/OFF Switch During CD playback you may slide the BASS BOOST switch to the ‘ON’ position to activate the Bass Boost function as desired. 9 HD8100R_031604.p65 9 16/3/2004, 14:18 Electronic Skip Protection (ESP) This CD player includes an Electronic Skip Protection circuit that continuously stores 60 seconds of CD music in an electronic memory. If the player is bumped or shaken you will not hear any skipping because the player is reading from the memory, not directly from the disc. Of course if the shaking continues for more than 60 seconds, the ESP memory will be depleted and the player may then skip or stop if the shaking continues. ESP memory function is automatically activated during playback. The display will show the ESP meter and begin to fill up with bars. Each bar represents approximately 12 seconds of music in the memory. When all 5 bars appear the memory contains 60 seconds of music. If the player is bumped or shaken one or more of the bars may disappear as the memory is depleted . When the shaking stops the memory will fill up again. To deactivate the ESP function, press the ESP button and the ESP meter will disappear in the display. Notes: • The ESP circuit draws additional current from the batteries. To extend the battery life leave the ESP circuit ‘Off’ when the unit is used in a stable location not subject to bumps and shakes. • When the ESP circuit is switched ‘On’ or ‘Off’ the sound will be interrupted for 2 to 5 seconds. This is normal and not an indication of any problem with the player. 10 HD8100R_031604.p65 10 16/3/2004, 14:18 11 NORMAL CD PLAYBACK • Make sure you have installed the batteries. • Make sure the HOLD switch is set to the ‘Off’ (left) position. • Make sure to set the VOLUME control to a low setting before you put on the headphones. IMPORTANT: This CD player can play normal CDs plus CD Recordable (CD-R) and CD Rewriteable (CD-RW) discs. However the playability of CD-R and CD-RW discs may be affected by the type of software that was used in ‘ripping’ the tracks from the original discs and ‘burning’ the tracks onto the blank media. Playability may also be affected by the quality and condition of the blank media you use for recording. 100% compatibility cannot be guaranteed. This is not an indication of any problems with your player. 1.) Slide the CD door OPEN switch to the right to unlock and open the CD door. 2.) Place your CD on the center spindle with the printed label side facing up. Press downward on the disc near the center hole until the disc is fully seated on the spindle. 3.) Close the CD door and connect the headphones to the headphone jack (green color) by pushing the headphone plug the into headphone jack until a ‘click’ sound is heard. 4.) Press the PLAY/PAUSE button to begin playback. The display will briefly show “60 SEC”, then “ – – “ flashes while the player reads the disc. The total tracks and playing time will appear briefly in the display and then the playback will begin on track 1. The display will show the elapsed playing time of the track being played. 5.) Adjust the VOLUME, and BASS BOOST controls as desired. OPEN HD8100R_031604.p65 11 16/3/2004, 14:18 6.) Playback will continue until the end of the disc, then the player will stop automatically and the display will again show the total tracks and playing time on the disc. After approximately 30 seconds the power switches ‘Off’ automatically to conserve the batteries and the display goes blank. To stop playback before the disc ends press the STOP button at any time. Press the STOP button after the disc has stopped to...