Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check – Upon the completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. Condensation – Moisture may form on the CD pickup lens when: -The unit is moved from a cold spot to a warm spot -The heating system has just been turned on -The unit is used in a very humid room -The unit is cooled by an air conditioner When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again. En ENGLISH 3 Power supply OPE/BATT The OPE/BATT indicator lights up while the power is on. Using on AC house current Connect the AC cord as illustrated below. to the AC inlet of the unit supplied AC cord to an AC outlet (AC 120 V, 60 Hz) CAUTION Use only the supplied AC cord. Use with other cords may result in the risk of fire. Using on batteries Open the lid of the battery compartment on the rear and insert eight R20 (size D) batteries, not supplied, as illustrated below. Then close the lid. To switch from AC power supply to battery supply, disconnect the AC cord from the AC inlet. R20 (D) When the OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation, replace the batteries. Notes on batteries To avoid damage from leakage or explosion, observe the following: • Insert the batteries with the 0and 9marks correctly aligned. • Do not mix different types of batteries or old batteries with new ones. • When the unit is not to be used for a long period, remove the batteries. • Never recharge the batteries, apply heat to them or take them apart. • Remove dead batteries. If liquid leaks from the batteries, wipe thoroughly to remove. Connections IMPORTANT • Make sure that the AC cord is disconnected and batteries are removed before connecting speakers. • Do not connect other than the supplied speakers. 1 Position the speakers. To couple with the speakers, slide each speaker down into the guide brackets on the center unit until the height is level with the unit. To separate the unit from the speakers, slide the speakers up and off, while pressing the speaker release knob. Release knob 2 Connect the speakers. Connect the right speaker cord to the R terminals, and the left speaker to the L terminals. Connect the speaker cord with the white broken line to 0and the other cord to 9. 4 ENGLISH Remote control Insert two R6 (size AA) batteries. R6 (AA) When the reach of the remote control signal is less than 5 meters (16 feet), replace the batteries. The remote control may not operate correctly when: -The unit is exposed to intense light, such as direct sunlight -Objects block the remote control signal to the unit To use the buttons on the remote control Buttons on the remote control and the main unit with identical indications have the same functions. To turn the power on Press POWER to turn on the display. When using the unit on the batteries, this button will not turn the power on. To turn the power off Press POWER to turn off the display. When one of the deck operation buttons is pressed, this button will not turn the power off. To use the FUNCTION button Each time FUNCTION is pressed while the power is on, the function is selected cyclically. CD RADIO *TAPE * applicable when one of the deck operation buttons is pressed FUNCTION POWER Specifications Tuner section Frequency range, antenna — FM: 87.5 - 108.0 MHz Rod antenna, AM: 530/531 - 1,710/1,602 kHz (10/9 kHz step) Ferrite bar antenna Deck section Track format — 4 tracks, 2 channels / Frequency range — Normal tape: 50 - 12,000 Hz (EIAJ) / Recording system — AC bias / Erasing system — Magnet erase / Heads — Deck 1: Recording/playback head (1), Erasure head (1); Deck 2: Playback head (1) CD player section Disc — Compact disc / Scanning method — Non- contact optical scanner (semiconductor laser) / Rotation speed — Approx. 500 - 200 rpm/CLV / Error correction — Cross interleave, Reed, Solomon code / Number of channels — 2 channels / D/A conversion — 1 bit DAC General Power requirements — DC 12 V using eight size D (R20) batteries, AC 120 V, 60 Hz / Dimensions (W . H . D) — 274 . 245 . 211 mm (10 7/8 . 93/4 . 83/8 in.) / Weight — 3.1 kg (6 lbs. 13 oz.) (excluding batteries) / Power output — 5 W + 5 W (EIAJ, 2.7 ohms DC) / Power consumption — 20 W / Accessories — AC cord (1), Remote control (1) Speaker Type — 120 mm cone type / Dimensions (W . H . D) — 160 . 236 . 170 mm (63/8 . 93/8 . 6 3/4 in.) / Weight — Approx. 0.9 kg (2 lbs.) . 2 / Impedance — 2.7 ohms / Allowable max. input — 7 W Specifications and external appearance are subject to change without notice. COPYRIGHT Please check the copyright laws relating to recordings from disc, radio or external tape for the country in which the machine is being used. If an erroneous display or malfunction occurs Make sure that none ...