Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
• Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. It may cause malfunction. • Do not load an unrecorded CD-R/RW disc. It will take over 30 seconds to read the disc. The disc may be damaged if you try to open the disc compartment while reading the disc. 0-9, +10 REPEAT MODE cPLAY aPAUSE r, t sSTOP PROGRAMMED PLAY Up to 20 tracks can be programmed from the disc. 1 In stop mode, keep *sSTOP/MEMORY pressed until program number flashes in the display. * or sSTOP on the remote control Program number 2 Press *r, tto select a track, then press sSTOP/MEMORY to store it. The next program number starts flashing. * or the numbered buttons 0-9 and +10 on the remote control 3 Repeat step 2 to program other tracks. 4 Keep sSTOP/MEMORY pressed until appears in the display to finish the program. indicates the unit stores the programmed tracks. 5 Press eto start play. To check the program, press ror tin stop mode. To clear the program, press sonce in stop mode so that disappears in the display. To change the programmed tracks, clear the program and repeat all the steps again. En ENGLISH 7 DUBBING A TAPE 1 Press TAPE/POWER/6STANDBY to turn the power off. 2 Insert a tape to be recorded on into deck 1 with the side to be recorded facing out. 3 Insert a tape to be played into deck 2 with the side to be played facing out. 4 Press athen press won deck 1 to enter recording pause mode. The power is turned on. cis pressed simultaneously. 5 Press HI-SPEED DUBBING to select a dubbing speed. The HI-SPEED DUBBING indicator lights up: Dubs at high speed. The HI-SPEED DUBBING indicator goes off: Dubs at normal speed. 6 Press con deck 2. aon deck 1 is released and recording starts. To stop recording, press Zon deck 1 and deck 2. The power will be automatically turned off. NOTE When recording near a television, noise may be recorded. Move the unit away from the television. En To prevent accidental erasure Break off the plastic tabs on the cassette tape with a screwdriver or other pointed tool after recording. To record on the tape again Cover the tab openings with adhesive tape, etc. Side A Tab for side A ENGLISH 9 VOLUME MIC VOL NUP, MDOWN DISPLAY MIC EQ EQ PHONES QSOUND VOL i, k REPEAT/ r, t r, t OSC/SLEEP GENERAL SOUND ADJUSTMENT Volume or tone adjustment does not affect recording. VOLUME (VOL) Press VOLUME NUP or MDOWN. The volume level is displayed as a number from 0 to 19. “1” in the display indicates the level 1 and “• 1” indicates the level 11. • The volume level is automatically set to 9 if the power is turned off when the volume level is set to 10 or more. (except when turning the power back on within 4 seconds) • Pressing DISPLAY on the remote control displays the adjusted volume level. 3-mode EQ (equalizer) Press EQ repeatedly until the desired mode is displayed. The equalizer mode changes to ROCK, POP, JAZZ or no equalization, cyclically. ROCK POP JAZZ ROCK - Emphasizes the high and low range of music. POP - Emphasizes voice and midrange of music. JAZZ - Emphasizes the low range of music. QSOUND system This system provides a rich, three dimensional sound area for stereo sources. You can enjoy more enhanced sound. Press QSOUND and the QSOUND indicator lights up. • At higher volumes, turning QSOUND on may cause sound distortion. In this case, make the volume down. SETTING THE SLEEP TIMER The unit can be turned off automatically at a specified time. 1 Keep REPEAT/OSC/SLEEP pressed until “• 1” flashes in the display. The dot and number flash. 2 Within 4 seconds, press ror tto specify the time until the power is turned off. Each time it is pressed, the time changes between 10 and 90 minutes in 10-minute steps. Example: The unit will turn off after 30 minutes. (off) 123 90 While the sleep timer works the dot keeps flashing. The volume level or a CD track number. To check the time remaining until the power is turned off Repeat step 1 shown above. The remaining time is displayed for 4 seconds. To cancel the sleep timer Display the remaining time and press ror t repeatedly until (off) is displayed. NOTE If the unit is turned off during tape playback, con the deck will not be released. Press Zto release c. 10 ENGLISH MICROPHONE MIXING Connect a microphone with a mini plug to the MIC jack and play a source to be mixed. To record the microphone mixing sound, insert a tape in deck 1 and press w. • During dubbing at high speed, the microphone mixing sound is not recorded. MIC VOL – Adjusts the microphone volume. If a howling sound is produced, turn the volume down. • To prevent howling, hold the microphone away from the speakers. The use of unidirectional type microphones is also recommended. En To listen with the headphones Connect headphones with a stereo mini plug to the PHONES jack. If an erroneous display or malfunction occurs Make sure that none of the deck operation buttons is pressed. Press swhile pressing TAPE/POWER/6STANDBY. If the unit cannot be reset in the way above, dis...