Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
The keys marked * are provided only on the remote control unit. 1 TIME DISPLAY key # 5 Numeric keys ( 1 11111 ~ ) ))))) , 0 00000 ) # 2 Program-related keys P.MODE key EDIT key CLEAR key CHECK key $ * %( %( 6 Basic function keys Skip keys (4,.) # Search keys (1,A) # Stop key (7) @ Play/Pause key (6) @ 3 RANDOM key 4 REPEAT key ) ^ *7 OUTPUT (DOWN, UP) key 7 11 1 5 2 3 4 6 7 Model: RC-P0715 Infrared ray system Loading batteries 1 Remove the cover. 2 Insert batteries. 3 Close the cover. O Insert two AA-size (R6) batteries as indicated by the polarity marking. 12 Operation OWhen pressing more than one remote control key successively, press the keys securely by leaving an interval of 1 second or more between keys. After plugging in the power cord, press the POWER switch of the main unit to turn the unit ON. When the unit is turned ON, press the key of the function to be operated. Operating range (Approx.) Remote control light sensor 0 30. 6m 30. NotesNotes 1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries. 2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones. 3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light sensor. In such a case, change the system installation position to prevent the malfunction. Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. 0 7 6 4 . 1 A The figure shows an example for the DPF-2030 : Keys and control used in the operations described on this page. Playing tracks in order from track No. 1 Press the POWER switch to ON.1 0 POWER -ON . OFF OPlayback starts when a disc has been loaded. 1Open the tray. 3Close the tray. 2Place a disc. Disc tray Label side 0 0 OPEN/CLOSE 0 OPEN/CLOSE 0 0 7 6 4 . 1 A 2 2 Load a disc. 3 3 Start playback. 0 6 ODo not touch the played side of disc. OLoading two discs together will cause malfunctioning. OPlace the disc properly along the groove on the tray. (If the disc is not placed horizontally, malfunction will result.) OA single CD (8 cm disc) can also be played. OOrdinary CD single (8 cm) disc adapters sold in audio stores cannot be used with this unit. Lights up. TRACK TRACK NO. 6 1 7 2 8 3 9 4 10 5 0:1000 The track Nos. recorded on the CD are displayed. OAfter a few seconds, play starts from the track No. 1. Elapsed time of track being played TRACK TRACK NO. SINGLE TIME 6 1 7 2 8 3 9 4 10 5 0:1005 Track NO. being played To pause playback To stop playback Lights up. OEach press pauses and plays the CD alternately. TRACK 0 6 0 7 Normal play (TRACK mode) Playback from desired track (except for DPF-1030) (Remote control unit only) Press the numeric keys as shown below.... To enter track No. 23 : 003 To enter track No. 40 : 0000) OPlayback starts from the selected track and continues on the subsequent tracks. 1 2 3 4 5 6 7 8 9 0 +10 REMOTE CONTROL UNIT RC-P0715 Skipping tracks To skip backward To skip forward 0 4 . OThe track in the direction of the pressed key is skipped, and the selected track will be played from the beginning. OWhen the 4 key is pressed once during playback, the track being played will be played from the beginning. Searching OPlayback starts from the position where the key is released. Forward search Backward search 0 1 A Time display on CD player (TIME DISPLAY) Each press of the TIME DISPLAY key changes the displayed contents. SINGLE TIME 1 : Elapsed time of track being played (SINGLE TIME 1:23 SINGLE TIME lights up.) 2 : Remaining time of track being played (SINGLE _2:37 TIME lights up.) : Elapsed time of entire disc (TOTAL TIME lights TOTAL TIME 3 23:45 up.) : Remaining time on entire disc (TOTAL TIME lights TOTAL TIME 4 _36:15 up.) 0 TIME DISPLAY OOnly the display 1 and 2 will be displayed in RANDOM and EDIT modes. Programmed play (PGM mode) 14 Use the following procedure to program desired tracks in a desired order. (up to 20 tracks) O Load a disc in the CD player. @Preparation 0 7 6 4 . 1 A The figure shows an example for the DPF-2030 1 1 Press so that the “PGM” indicator lights. Program desired tracks.2 Do this operation in the stop mode. 0 P.MODE Go to step 2 within 5 seconds. Start playback.32 Set the entry. 1 Select the desired track No. Press the numeric keys as shown below.... To enter track No. 15: 05 Go to step 2 within 5 seconds. 3 Repeat steps 1 and 2 above. 0 1 2 3 4 5 6 7 8 9 0 +10 P.MODE 4 . Main unit (Except for DPF-2030) Remote control unit (Except for DPF-1030) (Programming is not possible during playback) 0 6 : Keys and control used in the operations described on this page. Lights up. TRACK NO. 01 PGM Displays the entered program No. Displays the total playing time for a few seconds. of the programmed tracks. TRACK TRACK NO. NO. TOTAL TIME 02 P_ 01 02 _16:42 OUp to 20 tracks can be programmed. When “FULL” is displayed, no more tracks can be progra...
Otros modelos de este manual:reproductores de CD - DPF-1030 (784.56 kb)