Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit. The type plate is located on the bottom of the set. For users in the U.K., please follow the boxed instructions ‘Important notes... ’ on this sheet. Helpful hints : –To avoid unnecessar y energy consumption, always adjust the source selector to TAPE/OFF after using the set, and also check that the tape deck keys are released. Basic Operation/ Basic operation 1 To select your sound source, adjust the source selector to : CD, TUNER or TAPE/OFF. 2 To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released. Helpful hints: – To change from TAPE to TUNER or CD function, or when you are switching off the set: first, make sure you press the tape 9/ key to end playback and all the cassette keys are released. Adjusting volume Adjust the volume with the VOLUME control. Radio reception 1 Adjust the source selector to TUNER. 2 Adjust BAND to FM or MW as your desired band. 3 Turn TUNING to tune to a station. • For FM, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For MW, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. 4 To switch off the radio, adjust the source selector to TAPE/OFF position and check the cassette keys are released. CD Player Playing a CD This CD player plays Audio Discs including CD-Recordables and CD-Rewritable. • MP3 CD-ROMs, CD-I, CDV, VCD, DVD or computer CDs are not possible for playback on this set. IMPORTANT! • CDs encoded with copyright protection technologies by some record companies may be unplayable by this product. 1 Adjust the source selector to CD. 2 Open the disc door. 3 Inser t a CD with the printed side facing up and press the CD door gently to close. . Display shows -- and later, the total number of tracks. (See 2, 3) 4 Press 2; on the set to star t playback. . Display: 2 and the current track number. (See 4) 5 To pause playback press 2; .To resume playback, press 2; again. 6 To stop CD play, press 9. Helpful hints : CD play will also stop when: – you open the CD compartment; – you select TUNER, or TAPE/ OFF sound source; – the CD has reached the end of playback. Selecting a different track • Press . or § once or repeatedly until the desired track number appears in the display. • In the stop/pause position, press 2; to star t playback. Finding a passage within a track 1 During playback, press and hold down . / § . . The CD is played at high speed and low volume. 2 When you recognize the passage you want release . / § . . Normal playback resumes. Helpful hints : – When your searching reaches the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the stop position, press PROG to activate programming. . Display: PROG and 00 flash (see 5). 2 Press . or § to select your desired track number. . Display: PROG and your desired track number flash. 3 Press PROG to store the desired track number. . Display: PROG and 00 flash for you to program the next track. 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. 5 To play your program, press 2; . . Display: PROG flashes during program playback. CD Player Helpful hints : – If you tr y to store more than 20 tracks, no track can be selected and the display will flashing -- . To review a program • In the stop position, press PROG repeatedly to see your stored track numbers. Erasing a program You can erase the contents of the memor y by: – in the stop position, press PROG to enter program mode, and then press 9; – Selecting TUNER or TAPE/OFF sound source; – opening the CD door. . Display: PROG disappears. Different play mode (See 6) : REPEAT You can play the current track or the whole disc repeatedly, and combine REPEAT modes with PROGRAM. REPEAT – plays the current track continuously. REPEAT ALL– repeats the entire CD/program. 1To select play mode, press REPEAT once or more. . The display shows selected mode. 2 Press 2; to star t playback if in the stop/pause position. 3To return to normal playback, press REPEAT repeatedly until the modes are no longer displayed. – You can also press 9 to cancel your play mode. Cassette Recorder Cassette playback 1 Adjust the source selector to TAPE/OFF. 2 Press 9/ to open the cassette holder, and inser t a cassette and close the deck. 3 Press 1 to star t playback. 4 To pause playback press ; .To resume, press ; again. 5 To stop the tape, press 9/ . Fast forwarding/rewinding 1 Press 5 or 6 until you reach your desired passage. 2 Press 9/ to stop rewinding/fast forwarding. Helpful hints : – The keys are automatically released at the end of a tape and the set is switched off (unless PAUSE mode ; has been activated.) – During fast forwarding/rew...