Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
This set complies with the radio interference requirements of the European Community. Power Supply Whenever convenient, use the mains supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) 1 Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "–" symbols inside the compartment. (See 1) 2 Replace the compartment door, making sure the batteries are firmly and correctly in place. The set is now ready to operate. Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Using AC Mains 1 Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power cord to the AC POWER/MAINS inlet and the wall socket.The mains lead is now connected and ready for use. 3 To switch the set off completely, withdraw the power cord from the wall socket. • Disconnect the mains lead from the wall socket to protect your set during heavy thunderstorms. The type plate is located on the bottom of the set. For users in the U.K., please follow the boxed instructions ‘Important notes...’ on this sheet. Switching POWER on/off: Save energy To avoid unnecessary energy consumption, always adjust the source selector to TAPE/POWER OFF after using the set. Also check that the tape deck keys are released. General operation 1 To select your sound source adjust the source selector to : CD, TUNER or TAPE/POWER OFF. 2 Adjust the sound with the VOLUME control. 3 To switch off the set, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. Tuner reception 1 Adjust the source selector to TUNER. 2 Adjust BAND to select your desired waveband. 3 Turn TUNING to tune to a station. • For FM band signals, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For MW (AM or LW) band signals, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. 4 To switch off the radio, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. CD Player Display indication for CD functions: – OP: (See 2) CD door open – --: (See 3) reading disc contents / no disc/ error in CD operation or CD/ CDR is blank or not finalized (see Troubleshooting) – During CD playback: 2 and current track number – 2;: (See 4) playback on pause English Controls/Power Supply Power Supply General operation – prog: when CD program is active – Fu: program memory full Playing a CD This CD player plays Audio Discs including CD-Recordables. • CD-RWs, MP3 CD-ROMs, CD-I, CDV,VCD, DVD or computer CDs are not possible for playback on this set. 1 Adjust the source selector to CD. 2 Insert a CD/ CD-R with the printed side facing up and press the CD door gently close. 3 Press PLAY/PAUSE 2; on the set to start playback. 4 To pause playback press PLAY/PAUSE 2;. Press PLAY/PAUSE 2; again to resume play. 5 To stop CD play, press STOP 9. 6 To switch off the set, adjust the source selector to TAPE/POWER OFF position and check the cassette keys are released. Note : CD play will also stop when: - you open the CD compartment; - you select TUNER or TAPE/POWER OFF sound source; - the CD has reached the end of playback. Selecting a different track During playback you can use . / § to select a particular track. - If you have selected a track number in the stop or pause position, press PLAY/PAUSE 2; to start playback. • Press § once briefly for the next track, or press repeatedly until the desired track number appears in the display. • Press . once briefly to return to the beginning of a current track. • Press . repeatedly for a previous track. Finding a passage within a track 1 During playback, press and hold down . / §. • The CD is played at high speed and low volume. 2 When you recognize the passage you want release . / §. • Normal playback resumes. Note : When searching within a final track and you reach the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 32 tracks in the desired sequence. If you like, store any track more than once. 1 In the stop position, press PROG to activate programming. . Display shows 1 indicating the start of the program. prog flashes. (See 5) 2 Press . or § to select your desired track number. 3 Press PROG to store the desired track...