Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Note that, if the programmed track number isn’t found on the disc, that step is automatically erased. The program remains even after the Program Play ends When you press (, you can play the same program again. The program remains until you erase it If you replace discs, the programmed disc and track numbers remain. So, the player plays only the existing disc and track numbers. However, the disc and track numbers that aren’t found in the player or on the disc are deleted from the program, and the rest of the program is played in the programmed order. Note The total playing time doesn’t appear when: —You have programmed a track whose number exceeds 20. —The total playing time of the program exceeds 200 minutes. Checking the track order You can check your program before or after you start playing. Press CHECK on the remote. Each time you press this button, the display shows the disc and track number of each step in the programmed order. (When a whole disc is programmed as one step, “AL” appears instead of the track number.) After the last step in the program, the display shows “–END–” and returns to the original display. If you check the order after you start playing, the display shows only the remaining steps. Changing the track order You can change your program before you start playing. To You need to Erase a step Press CHECK until the track or disc you don’t want appears in the display, then press CLEAR Erase the last step in Press CLEAR. Each time you press the program the button, the last track or disc will be cleared. Add steps to the end Follow Steps 2 to 4 in “Creating Your of the program Own Program” on page 11 Change the whole Hold down CLEAR until “ALL program completely CLEAR” appears in the display to erase the whole program, then create a new program following Steps 2 to 4 in “Creating Your Own Program” on page 11 Playing Using a Timer (CDP-CA9ES only) You can start playing a disc at any time you want by connecting a timer (not supplied). Please also refer to the instructions for the timer if you need help. TIMER Play mode buttons 1EPress one of the play mode buttons to select the play mode you want. 2ESet TIMER on the player to PLAY. 3ESet the timer to the time you want. The player turns off. When the set time comes, the player turns on and starts playing. 4EAfter you have used the timer, set TIMER on the player to OFF. Recording From CDs Recording From CDs Recording Your Own Program You can record the program you’ve created on a tape, DAT or MD. The program can contain up to 32 tracks. By inserting a pause during programming, you can divide the program into two for recording on both sides of a tape. DISC 1 – 5 (PROGRAM Number buttons >10 P 1ECreate your program (for side A when recording on a tape) while checking the total playing time indicated in the display. Follow Steps 1 to 4 in “Creating Your Own Program” on page 11. The A indication appears in the display. 2EWhen you record on both sides of the tape, press Pto insert a pause. The “P” and AB indications appear in the display and the playing time is reset to “0.00.” When you record on one side of the tape or on a DAT or MD, skip this step and go to Step 4. A pause is counted as one track You can program up to 31 tracks when you insert a pause. 3ERepeat Steps 2 to 4 in “Creating Your Own Program” on page 11 to create the program for side B. 4EStart recording on the deck and then press (on the player. When you record on both sides of the tape, the player pauses at the end of the program for side A. 5EWhen you record on side B, reverse the tape and press (or Pon the player to resume playing. You can check the total playing time while programming (Program Edit) To select a track, press or ±and check the total playing time. Then press PROGRAM to confirm your selection. To check and change your program See page 12. The A indication appears while checking the program for side A and B while checking the program for side Fading In or Out You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector. RM-D645 for CDP-CA9ES Number buttons FADER RM-D515 for CDP-CA8ES Number buttons FADER To Press FADER Start play fading in During pause. The Qindication flashes and play fades in. End play fading out When you want to start fading out. The qindication flashes. The play fades out and the player pauses. Changing the fading time You can change the fading time from 2 to 10 seconds before fading in or out. If you don’t change it, fading lasts for 5 seconds. 1EPress FADER before you start playing. “FADE 5 SEC” appears in the display. 2EWhile the fading time “5” is flashing, press the number button to specify the fading time. B. 13E ( Storing Information About CDs (Custom Files) (CDP-CA9ES ( Storing Information About CDs (Custom Files) (CDP-CA9ES What You Can Do With the Custom Files The player can store 4 types of information called “Custom Files” for ea...
Otros modelos de este manual:reproductores de CD - CDP-CA8ES (556.6 kb)