|
Resumen del manual
The memory counter will flash as the extra split/lap times are being displayed. The icon "FULL" will be steadily ON. The maximum memory counter value is 100 or 500. To stop the chronograph, press [STOP]. The indicator "STOP" will come on again to show the status. Press [RESET] as the stopwatch stops to reset the stopwatch while the split/lap times will be kept in memory. When the stopwatch starts running from reset state, all the lap memories will be cleared. Decimal Timing (AE790M500DEC model only) 1. The DM Model can operate as a normal 1/100 second chronograph as well as decimal minute, decimal second, and decimal hour chronograph. As you press [MODE] to enter the chronograph mode, the normal 1/100 second chronograph display will be shown. {000} 0: 00' 00" 00 SPLIT 0: 00' 00" 00 LAP STOP 0: 00' 00" 00 Reset the chronograph to 00, then press [LAP/SPLIT] to go to the second chronograph mode. (1/100s).You will note the change by looking at the bottom of the display to see 1/100s. {000} 0 0 0 0 0. 0 0 SPLIT 0 0 0 0 0. 0 0 LAP STOP 0 0 0 0 0. 0 0 1/100S Change to the 1/1000 of a minute chronograph mode by pressing [LAP/SPLIT] again. (1/1000M) {000} 0 0 0. 0 0 0 SPLIT 0 0 0. 0 0 0 LAP STOP 0 0 0. 0 0 0 1/1000M Go to the 1/10,000 hour chronograph by pressing [LAP/SPLIT] again.(1/10,000H) {000} 0. 0 0 0 0 0 SPLIT 0. 0 0 0 0 0 LAP STOP 0. 0 0 0 0 0 1/100000H Please note that if the stopwatch has started running (or is running), no selection for chronograph operating modes can be made until the stopwatch has been stopped and reset. Segmented run memory for lap/split time storage: A header consisting of the date/time stamp is attached to each segment to indicate the moment when you began recording the particular timing segment. To get to this feature, press [MODE] in chronograph mode to enter DATA mode when the stopwatch has been stopped. Records for different segments can be recalled, read or deleted. Detailed operation in "DATA" mode is described in Data Mode section below.. Chronograph Data Recall Mode Press [RECALL] in Chronograph mode to recall stored split/lap time memories. The mode message will be shown up for one to two seconds as mode message display is enabled. RECALL The split and lap time will be displayed on the upper and the middle line respectively. The lower line shows the current stopwatch counting. During data recall, the fastest lap time will be reviewed first. RECALL FAST {004} 0: 01' 12" 34 SPLIT 0: 00' 01" 60 LAP RUN 0: 03' 06" 52 Then comes the slowest lap time by further pressing of [RECALL]. RECALL SLOW {001} 0: 00' 07" 63 SPLIT 0: 00' 07" 63 LAP RUN 0: 03' 10" 16 Press [RECALL] again to view the average lap time. RECALL AVG {005} 0: 00' 05" 12 LAP RUN 0: 03' 16" 03 Press [RECALL] continually to review all the stored split/lap times. The sequence starts from the last record to the first record when the stopwatch is running and vice versa when the stopwatch has been stopped. RECALL {005} 0: 00' 14" 91 SPLIT 0: 00' 02" 05 LAP RUN 0: 03' 28" 94 [RECALL] RECALL {004} 0: 00' 12" 86 SPLIT 0: 00' 01" 60 LAP RUN 0: 03' 33" 64 [RECALL] RECALL {003} 0: 00' 11" 26 SPLIT 0: 00' 01" 78 LAP RUN 0: 03' 40" 15 [RECALL] RECALL {002} 0: 00' 09" 48 SPLIT 0: 00' 01" 85 LAP RUN 0: 03' 45" 34 [RECALL] RECALL {001} 0: 00' 07" 63 SPLIT 0: 00' 07" 63 LAP RUN 0: 03' 48" 01 After recalling the first record, press [RECALL] once more to exit from Recall mode and go back to chronograph mode. The "RECALL" icon will be OFF. [RECALL] {005} 0: 03' 50" 11 SPLIT 0: 00' 42" 60 LAP RUN 0: 03' 50" 11 During memory recall, you can press either [START], [STOP] or [LAP/SPLIT] to exit from chrono recall mode and jump to the chrono start/stop or lap state respectively. Data Mode (AE760M & AE790M Model only) Press [MODE] until you enter DATA mode The mode message "DATA" will be shown for one to two seconds before the number of free memories is to be shown. FREE 95 LAP You can press [START] to scroll through all segments. The current segment will come first. RECALL {008} 2 0 0 1 SEG {002} 2 - 1 9 A 10: 15' 30 The header consisting of the date/time stamp will be shown. The number of laps in the segment will appear in the upper left while the segment number is displayed in the middle left. If the segment shown is not your desired segment, press [START] to reach the desired segment. The current segment will be accessed first, then it will cycle back to the 1st, then 2nd and so on. When you have found the segment you want, you can press [RECALL] button consecutively to read the lap records from the first to the last lap. RECALL {001} 0: 01' 00" 55 SEG SPLIT {002} 0: 00' 12" 86 LAP 0: 01' 00" 55 RUN As you continue to press [RECALL] during the display of the last lap, you can advance to the next segment by pressing [START], The front page of the segment will be shown. Say the next segment is SEG 1. RECALL {012} 2 0 0 1 SEG {001} 2 - 1 8 A 10: 00' 15 How to delete individual memory segments: Search the desired segment first as described abo...
Otros modelos de este manual:Relojes - AE790M500 (368.23 kb)
Relojes - AE790M500DEC (368.23 kb)
Relojes - AE760M100 (368.23 kb)