Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
To specify the illumination duration 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C nine times so the illumination duration setting screen is on the display. 3. While the illumination duration setting is flashing, press D to toggle the setting between one second ( ) and three seconds ( ). 4. Press A to exit the setting screen. About the Auto Light Switch While the auto light switch is enabled, illumination turns on for about one second or three seconds, whenever you position your wrist as described below in any mode. Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes illumination to turn on. Parallel to ground More than 40° Mode Timekeeping World Time Countdown Timer Stopwatch Alarm Hand Setting Graphic Area A Timekeeping Mode seconds Timekeeping Mode seconds Countdown time minutes Stopwatch time seconds No indication No indication Graphic Area B Timekeeping Mode minutes Timekeeping Mode minutes Countdown time seconds Stopwatch time 1/10 seconds No indication No indication Mode Timekeeping World Time Countdown Timer Stopwatch Alarm Hand Setting Graphic Area Timekeeping Mode seconds Timekeeping Mode seconds Countdown time minutes Stopwatch time seconds No indication No indication Reference This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch. Graphic Area The following describes the information indicated by the graphic area in each mode. [Module 3319] Graphic area [Module 3781] Graphic area B Graphic area A Auto Return Feature If you leave a screen with flashing digits on the display for two or three minutes without performing any operation, the watch automatically exits the setting screen. • To set a one-time alarm, display one of the screens indicated by an alarm number from AL1through AL4. To set the snooze alarm, display the screen indicated by SNZ. • The snooze alarm repeats every five minutes. 2. After you select an alarm, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. • This operation automatically turns on the alarm. 3. Press C to move the flashing between the hour and minute settings. 4. While a setting is flashing, use D (+) and B (–) to change it. • When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator). 5. Press A to exit the setting screen. Alarm Operation The alarm sounds at the preset time for about 20 seconds, regardless of the mode the watch is in. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, or until you turn the alarm off . • Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode digital time. • To stop the alarm tone after it starts to sound, press any button. • Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation. Displaying the Timekeeping Mode setting screen Displaying the SNZ setting screen To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn an alarm on and off 1. In the Alarm Mode, use D to select an alarm. 2. Press A to toggle it on (ON displayed) and off (OF displayed). • Turning on a one-time alarm (AL1through AL4) displays the alarm on indicator on its Alarm Mode screen. • Turning on the snooze alarm (SNZ) displays the alarm on indicator and snooze alarm indicator on the Alarm Mode snooze alarm screen, and in all other modes. • In all modes (except for the Alarm Mode), the alarm on indicator is shown for any alarm that is currently turned on. • The alarm on indicator flashes while the alarm is sounding. • The snooze alarm indicator flashes during the 5-minute intervals between alarms. Warning! • Always make sure you are in a safe place whenever you are reading the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not surprise or distract others around you. • When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury. To turn the auto light switch on and off In any mode, hold down B for about two seconds to toggle the auto light switch on (auto light switch indicator displayed) or off (auto light switch indicator not displayed). • The auto light switch indicator is on the display in all modes while the auto light switch is turned on. • In order to p...
Otros modelos de este manual:Relojes - 3319 (816.02 kb)