Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
Remember that not all countries or even local areas use Daylight Saving Time. l l l l ll llll l l l l DST indicator On/Off status To toggle the Timekeeping Mode digital time between DST and Standard Time 1.In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C once and the DST setting screen appears. 3. Press D to toggle between Daylight Saving Time (ON displayed) and Standard Time (OF displayed). 4. Press A twice to exit the setting screen. • The DST indicator appears on the Timekeeping, Hunting/Fishing, Alarm, and Hand Setting Mode screens to indicate that Daylight Saving Time is turned on. In the case of the Hunting/Fishing Mode, the DST indicator appears on the hunting/fishing level screen only. Home Site Data Moon phase, the hunting/fishing level indicator, and Hunting/Fishing Mode data will not be displayed properly unless Home Site data (UTC differential and longitude) is configured correctly. • The UTC differential is a value that indicates the time difference between a reference point in Greenwich, England and the time zone where a city is located. • The letters UTC is the abbreviation for Coordinated Universal Time, which is the world-wide scientific standard of timekeeping. It is based upon carefully maintained atomic (cesium) clocks that keep time accurately to within microseconds. Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s rotation. Operation Guide 4734 4735 2 • The “Site Data List” provides UTC differential and longitude information around the world. • The following is the initial factory default Home Site data (Tokyo, Japan) when you first purchase the watch and whenever you have the batteries replaced. Change these settings to match the area where you normally use the watch. UTC differential (+9.0); Longitude (East 140 degrees) ll l l ll l l llll ll Longitude value Longitude (east/west) To configure Home Site data 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C twice to display the UTC differential setting screen, and confirm that the setting is correct. • If the UTC differential setting is not correct, use D (+) and B (–) to change it. 3. Press A to display the longitude value setting screen. 4. Press C to toggle the flashing between the longitude value and the longitude unit (east/west). 5. While the setting you want to change is flashing, use D and B to change it as described below. Setting Longitude Value Longitude Unit (East/West) Button Operations Use D (+) and B (–) to change the setting. • You can specify a value from 0° to 180°, in 1- degree units. Use D to switch between east longitude ( ) and west longitude ( ). Screen 6. Press A to exit the setting screen. Setting the Analog Time Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display. ll l l l l l l lllll l To adjust the analog time 1. In the Timekeeping Mode, press C seven times to enter the Hand Setting Mode. 2. Hold down A until the current digital time starts to flash, which indicates the setting screen. 3. Use D to adjust the analog setting. • Press D once to advance the hands 20 seconds. • Hold down D to advance the hands at high speed. • To lock high speed hands movement, hold down D to start it and then press B to lock. The hands will continue to advance for one 12-hour cycle or until you press any button to stop it. It will also stop automatically after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts to sound. 4. Press A to exit the setting screen. • The minute hand will be adjusted slightly to match the seconds when you exit the setting screen. • To return to the Timekeeping Mode, press C. Hunting/Fishing Mode The Hunting/Fishing Mode displays an indicator that shows, as one of five levels, the suitability of a specific date and time (minute 00 to minute 59 of a particular hour) for hunting or fishing. This mode also can be used to display Moon Data (Moon age and Moon phase) for a specific date. • If you suspect that the hunting/fishing level indicator or current Moon data is wrong for some reason, check the current Timekeeping Mode settings (time, date, and Home Site), and correct them if required. • See “Moon Phase Indicator” for information about the Moon phase indicator. • All of the operations in this section are performed in the Hunting/Fishing Mode, which you enter by pressing C. Month – Day Time HUNT/FISH indicator Moon phase indicator Hunting/Fishing Level Screen Hunting/Fishing level indicator Hunting/Fishing Level Indicator The hunting/fishing level indicator shows the relative favorability of a hunting/fishing time (calculated in accordance with Moon transit and phase) as shown in the table below. Module Level 5 Level 4 Level 3 Level 2 Level 1 4734 4735 Upper Lower West East Moon Transit Other Moon Phase New moon*...
Otros modelos de este manual:Relojes - 4734 (1001.72 kb)