Votos - 10, Puntuación media: 3.9
(
)
)
|
Resumen del manual
Follow all warnings and operating recommendations in this manual. Keep this manual for future reference. /*\ ATTENTION! /*\ / ■ \ Risk of electric shock! DO NOT OPEN! Warning: To prevent fire or shock hazard do not expose the appliance to rain or moisture. To prevent shock hazard do not remove the cover yourself. Apply to a service centre for repair and maintenance. A This lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. /i\ / ■ \ The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the manual accompanying the appliance. PRECAUTIONS 1. Before operating the units, read the instruction carefully. 2. Do not immerse the units into water. 3. Do not use abrasives or substances causing damages of the body and inner parts to clean the units. 4. Do not apply hard efforts to the units, do not subjects the units to strikes (dust and humidity are also contraindicated), as it can lead to failures and correspondingly to the reduction of life time, damages of the batteries and to the deformation of the body details. 5. If you break the unit; it will lead to the ending of guarantee. There are no details, demanding attention of the user inside it. 6. Use only new and specified in the manual batteries. Do not use old and new batteries together. 7. While long operation of the sensor in the conditions of extreme temperatures, the voltage of its batteries can be lowered, the operation radius of the remote sensor will be reduced. 4 4IM.indd 4 20.08.2008 15:57:03 6404IM.indd 5 English DESCRIPTION BASE UNIT 1. Display Displaying of current time (a), date (b), sunrise (c) and sunset time (d), temperature and humidity values from the remote sensor (e) and inside the room (f), pressure (g), lunar phases (h) and symbolic weather forecast (i). 2. The Max/Min/+ button. Displaying of maximal/minimal temperature, setting of current time, alarm time, date, as well as temperature and humidity value limits. 3. The Mode button Switching between the current time modes Clock 1/Clock 2, Alarm 1/Alarm 2 modes, entering the set up mode. 4. The Alarm/Channel/°C/°F button Switching on/off of Alarm 1/ Alarm 2 modes, signal switching from the remote sensors (from 1 till 4). 5. The Select/- button Setting the current time, alarm, date as well as temperature and humidity value limits. 6. The Snooze/Light button Activation of the snooze function and switching of the backlight of the display. 7. Battery compartment (for three “AA” batteries) 8. Wall-mount holder 9. Table stand REMOTE TEMPERATURE AND HUMIDITY SENSOR 10. LCD-display reflect temperature and humidity values 11. The SET button Entering of HOUSE CODE, adjusting of channels. 12. External wire sensor jack 13. The °C/°F button Switching between the Celsius and Fahrenheit scales, change of channels and house code. 14. Battery compartment (for three “AA” batteries) 15. Wall-mount holder/table stand 16. External wire sensor BEFORE YOU BEGIN For best operation insert the batteries firstly in the remote sensor and then in the base unit. Placing batteries in the remote sensor 1. Unscrew the screws on the battery compartment lid. Insert 2 batteries (“AA”, 1.5 V), following the polarity. 2. The HOUSE CODE will start flashing on the LCD-display for 8 seconds. HOUSE CODE - is a frequency signal, sent from the remote sensor to the base unit. All remote sensors in your system should have the same HOUSE CODE. 5 20.08.2008 15:57:03 English 3. Select the HOUSE CODE (from 1 till15) by pressing the °C/°F button. Press the SET button to store it in memory. 4. The number of the channels will start flashing on the LCD-display during 8 minutes. _ ~'~0!h Select the data transfer channels by pressing the °C/°F button. Press the SET button, to store it in memory. The base unit can receive signals from four sensors, that is why each sensor is given a certain number of channels. Note: for symbol forecast data of the first channels are used, that is why the corresponding remote sensor should be located outside the room. 5. Temperature and humidity values will be displayed by turns. 1 in c r ' I ? 3j 6. To switch between °C/°F press the °C/°F button. 7. Close the battery compartment lid and tighten up the screws. Note: if your meteorological station registers signals from nearby sources, use another HOUSE CODE. Factory settings: HOUSE CODE = 01, channel = 01. Placing batteries into the base unit 1. Open the battery compartment lid on the base unit. 2. Set 3 batteries (“AA”, 1.5 V), following the polarity. 3. Close the battery compartment lid. Battery replacement When the corresponding indication about battery discharge ( ) a...