Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
•The light also turns on for the first four seconds that the alarm sounds. •The volume of the alarm sound cycles through five levels as it sounds. Stopping the Alarm •When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on, the alarm will sound again in about five minutes. •To turn off the snooze feature, slide the Alarm Mode selector (2) to OFF. GENERAL GUIDE 11111SNOOZE/LIGHT button •Press this button to illuminate the display for about four seconds. •Pressing this button while the alarm is sounding stops the alarm. 22222Alarm Mode selector SNZ: Snooze alarm on ON: Alarm on OFF: Alarm off 33333UP (+) / DOWN (–) buttons Use these buttons to change the alarm time or the setting that is flashing on the display. 44444°C/°F button Press this button to toggle the temperature units between Celsius and Fahrenheit. 55555SET button Use this button when setting the current time. 66666CLEAR button Press this button to clear the currently displayed high/low temperature or humidity. 77777MAX/MIN TEMP. button Press this button to display the high and low temperature values. 88888RESET button Press this button to reset the clock after replacing its batteries. 99999MAX/MIN HUMIDITY button Press this button to display the high and low humidity values. USING THE CLOCK 1. Press the SET button (5) to cycle through the setting screens as shown below. 12-hour/24-hour Timekeeping ScreenTime Setting ScreenMonth and Day Setting ScreenYear Setting Screen Normal Timekeeping Screen 2. While the screen you want is displayed, use the DOWN (–) and UP (+) buttons (3) to change the flashing digits. UP (+)DOWN (—) RESET TEMP. MAX/MIN HUMIDITY MAX/MIN UP (+) DOWN (–) SET CLEAR°C /°F Press UP (+) to increase the flashing digits. Press DOWN (–) to decrease the flashing digits. Press UP (+) to increase the flashing digits. Press DOWN (–) to decrease the flashing digits. DQ-960 DQ-961 Alarm Mode selector SNZ ON OFF Description The alarm sounds at the preset time for one minute, and seven more times every five minutes thereafter. Even if you stop the alarm by pressing the SNOOZE/LIGHT button (1), the alarm sounds again five minutes later. •The indicator flashes on the display to indicate that the snooze feature is activated. The alarm sounds at the preset time for one minute. The alarm does not sound. Operation Guide DQ-960/961 3 USING THE LIGHT Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark. Important! •Overuse of the light can shorten battery life. THERMOMETER FUNCTIONS A built-in sensor measures temperature and shows the measured value on the display. The readout from the temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F). Temperature Measurements •The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above 70°C (158°F). •Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such readings are actually outside the guaranteed temperature range of this clock. Switching between Celsius and Fahrenheit •Push the °C/°F button (4) to select either Celsius (°C) or Fahrenheit (°F). °C/°F button (4) °C °F Celsius (°C) Fahrenheit (°F) High Temperature and Low Temperature Memory •The clock remembers the high and low temperatures it measured since the last time its temperature memories were cleared. You can recall these values as shown below. Current temperature and humidity MAX/MIN TEMP. button (7) High temperature and low temperature •To clear the high temperature and low temperature memory, press the MAX/MIN TEMP. button (7) to display the current high/low values, and then press the CLEAR button (6). Note that the current high/low values are displayed for only about five seconds, and you need to press the CLEAR button (6) during that period. New data starts to be stored after memory is cleared. CLEAR button (6) HYGROMETER FUNCTIONS A built-in sensor measures humidity and shows the measured value on the display. Humidity Measurements •The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 90%. High Humidity and Low Humidity Memory •The clock remembers the high and low humidity values it measured since the last time its humidity memories were cleared. You can recall these values as shown below. Current temperature and humidity MAX/MIN HUMIDITY button (9) High humidity and low humidity •To clear the high humidity and low humidity memory, press the MAX/MIN HUMIDITY button (9) to display the current high/low values, and then press the CLEAR button (6). Note that the current high/low values are displayed for only about five seconds, and you need to press the CLEAR button (6) during that period. CLEAR button (6) BATTERY REPLACEMENT Replace batteries whenever the display of the clock becomes dim and difficult to read. 1. Open the battery compartment cover as shown in the illustration. 2. Remove all of...