Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
( 2 ! & * # 3 @ % ^ $ 4 1 5 6 ) 8 9 0 7 1 X 2 3 4 5 6 7 English Controls Power supply Congratulations on your purchase and welcome to Philips! To fully benefit from the suppor t that Philips offers, register your product at Supplied accessory Line-in cable (used for audio input connection) Controls (see 1) 1 REPEAT ALARM – pushes to switch off alarm for a 6-minute period 2 LCD Display – shows the clock/ alarm time or CD/radio information 3 POWER – switches the set on or to standby – stops the active buzzer, radio or CD alarm for 24 hours – switches off the sleep timer 4 ALARM 1/ ALARM 2 – sets and activates alarm of ALARM 1 /ALARM 2 – stops the active buzzer, radio or CD alarm for 24 hours 5 CLOCK – sets clock time 6 SHUF/REP – selects different CD play modes: e.g. REPEAT or SHUFFLE (random order) 7 ./ § – adjusts clock / alarm time – skips CD tracks/ searches for a par ticular passage 8 9 – stops CD playback – erases a CD program 9 ); – star ts/ pauses CD playback 0 PROG – programs CD tracks ! LIFT TO OPEN – lift here to open CD door @ DISPLAY – displays CD tracks or radio information # AUX – 3.5mm audio input jack $ TUNING – tunes to a radio station % BAND – selects waveband: FM or MW ^ SLEEP – switches on/off radio, CD for timer mode – adjusts timer options for radio/CD playback & VOLUME – adjusts sound level * CD•RADIO•BUZZER – selects CD or radio sound source – selects CD radio, or buzzer or alarm mode ( Power cord – connects to wall outlet ) Pigtail – FM antenna to improve FM reception . Battery compartment – inser t a 9 volt battery, typed 6F22 (not supplied) for clock memor y backup Power supply 1 Check if the power voltage as shown on the type plate on the base of the set corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power plug to the wall outlet. The power supply is now switched on and the numbers on the display shows 0:00. You will need to set the correct time. 3 To disconnect the set from the power supply completely, unplug from the wall outlet. The type plate is located on the bottom of the set. For users in the U.K., please follow the boxed instructions ‘Important notes...’ on this sheet. Clock Radio Clock memory backup When a power failure occurs, the complete clock radio will be switched off. When the power supply returns, the time display shows 0:00 and you will need to reset the correct time on the clock. To retain the clock time and the set alarm time(s) in the event of an AC power failure or disconnection, inser t a 9 volt batter y, typed 6F22 (not supplied) into the batter y compar tment. This will act as a clock memor y backup. When powered by the battery, the time will not be illuminated on the clock display, and operation of the alarms, FM/ MW radio and CD are also impossible. As soon as the AC power supply returns, the display will indicate the correct time. 1 Inser t the batter y into the batter y compar tment for clock memory backup. 2 Connect the power plug to the wall outlet. • Replace the battery once a year, or as often as necessar y. Batteries contain chemical substances, so they should be disposed of properly. Setting the clock The clock uses 24-hour time format. You may set the clock from 0:00 if the set is disconnected from the wall outlet. 1 Press and hold CLOCK until clock digit for hour flashes. . It will exit the clock setting mode without setting if there is 5-second inactivity. 2 Press repeatedly, or hold down . / § to adjust the hours. 3 Press CLOCK to confirm the hour setting. . The clock digits for minute flash. 4 Press repeatedly, or hold down . / § to adjust the minutes. 5 Press CLOCK to confirm the setting. Radio 1 Press POWER to switch on from standby. . The display lights up. 2 Select RADIO source by pushing CD•RADIO•BUZZER to RADIO (located on the side panel). . “TUNER” is displayed. 3 Push BAND to FM or MW to select desired waveband. 4 Turn TUNING to find your station. 5 To adjust the sound, turn VOLUME. 6 To view radio information, press DISPLAY. . The current waveband and frequency will be displayed for several seconds (See 2), then it will switch back to clock display. 7 To switch off radio and back to standby, press POWER. . The display lights off. To improve reception: FM: Extend and adjust the pigtail for optimum reception. MW: Uses a built-in antenna. Direct the antenna by adjusting the position of your unit. This set complies with the radio interference requirements of the European Community. CD Player CD playback This CD clock radio can play only audio discs including CD-R (CD-recordable), CD-RW (CD-rewritable). Do not tr y to play a MP3-CD, CD-ROM, CD-RW, CDI,VCD, DVD or computer CD. 1 Press POWER to switch on from standby. . The display lights up. 2 Select CD source by pushing CD•RADIO•BUZZER to CD. . “CD” is displayed. 3 Lift the CD door to open. 4 Inser t a CD with printed side facing up, and close the CD door. . Flashing ---- is displayed briefly, then tota...