Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Failure to properly attach wheels could cause the wheels to fall off, resulting in an accident and serious injury. Direct impacts against the pivoting stroller wheels could cause damage to the wheel arm attachment brackets. The following safety precautions should be followed, otherwise injury or death to you or to your passengers could result: – Use wrist safety strap at all times. – Always use seat belts. – Always use parking brake when stroller is stationary. – Never in-line skate with the stroller kit. – Never climb or descend stairs with the stroller. – Use extreme caution on hills. 13 1313 JOGGING CTS KIT JOGGING CTS KITJOGGING CTS KIT 3.0 Installation Remove any other conversion kits from the wheel wheel arm attachment bracket. Insert the wheel arms by pressing the small button and sliding the arm into the wheel arm attachment bracket. The large button should engage into the hole on the wheel arm attachment bracket. WHEEL ARM WHEEL BRACKET QUICK RELEASE LEVER Close the quick release lever by pushing it flat against the wheel bracket. When the nut is properly adjusted, you will feel resistance halfway through tightening the lever. Make sure the lever is closed towards the back of the carrier. WARNING: Failure to properly attach wheels couldcause the wheels to fall off, resulting inan accident and serious injury. Install the quick release axle through the wheel’s hollow axle with a spring on each side of the wheel. Screw the nut onto the other side of the skewer axle. WARNING: Overloading the carrier with more than2.2lb (1kg) in the rear storage pouchescan make the carrier unstable. Slide the wheel axle all the way into thewheel bracket dropouts. With the quick release lever opened 90o to the wheel brackets (ie. pointing straightout), hand-tighten the nut on the back sideof the quick release skewer. WARNING: The following safety precautions shouldbe followed otherwise injury or death toyou or to your passengers could result: – Use wrist safety straps at all times. – Always use seat belts. – Always use parking brake whenstroller is stationary. – Never in-line skate with the joggingkit. – Never climb or descend stairs with the jogging kit. – Use extreme caution on hills. 14 1414 3.1 Storage There are 3 straps attached to the outsideof the storage compartment that you canuse to attach the front wheel of your joggerto in the event you have purchased both aCycling kit and Jogging kit but wish to keepthe Jogging kit components with the carrier. The wheel arms can be placed inside thestorage compartment or on the side of thecarrier if you own a Cougar or a CX carrier. CYCLING CTS KIT CYCLING CTS KITCYCLING CTS KIT The wheel arms can be stored on the side of the carrier. Press down the small button, and insert the wheel arm into the bracket located on the side of the carrier. The large button should engage into the hole in the bracket. Keep the left wheel arm on the left side ofthe carrier and right arm on the right side sothat the arm’s dropouts rest under the carri- er’s lower frame. WARNING: Read and understand all of the warnings otherwise injury or death to you or to your passengers could result: – Always use safety flag. – Avoid all obstacles as carriers can tip – Child must be old enough to wear a over causing serious injuries to the helmet and to sit upright unattended. – Do not operate the bicycle trailer passenger and cyclist. Consult pediatrician if child is less without reading and understanding this that one year old. manual. – Passenger must always use seat beltsand wear an approved helmet. – Child’s head, including helmet, must – Use extreme caution while trailering, not protrude above upper frame. never exceed 25 km/h and slow down – Child’s head, including helmet, must to less than 10 km/h around corners not protrude above upper frame. – Do not exceed the maximum capacity and on rough roads. for a single carrier of 75lb (34kg) and – Never leave child unattended in carrier. for a double carrier of 100 lb (45kg) – Cyclist must be an experienced, including children and cargo. strong rider. 15 1515 4.0 Reflectors and Flag Assembly PLASTIC CAP Attach the reflector to the spokes. Insert the orange clip into the reflector and over the spoke. With a slot screwdriver, turn the clip until reflector is tight and unable to shift. Attach the red reflector to the left grommet on the rear of the back storage bag. 4.1 Attaching Your New Quick Release (QR) Skewer & Axle Mounted Hitch Cup to Your Bicycle Note: the small diameter of the Skewer Springs should point inward towards thehub axle. Position the Hitch QR Lever so it points straightout from the hub (open position). Tighten theQR Nut on the opposite end of the Hitch QRSkewer until finger tight. Remove your existing QR skewer from yourbicycle rear wheel hub. Remove the QR nut andone Skewer Spring from the Hitch QR Skewer. Insert the Hitch QR Skewer making sure thatthe cup washer is next to the QR Lever andthe Axle Mounted Hitch Cup is on the outsideof the b...