Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Tel: +603-3341 9052. Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland. Assembled Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Both Shown Actual Size Note: Tighten all assembled screws with the enclosed Allen wrench. 2 Swing Housings Seat Bottom Seat Back 2 Side Rails Seat Pad Toy Bar Allen Wrench Base Hinge Rod Frame M6 x 25 mm Screw – 2 #8 x 2,5 cm Screw – 7 3 Assembly 2 • Position one of the swing housings so that the swing arm is facing the inside of the assembly. • Fit the swing housing onto the frame tube. Hint: The swing housing is designed to fit one way. If it does not seem to fit, try assembling it to the other frame tube. Swing Arm Frame Tube 1 • Insert and “snap” the base into the sockets in each side of the frame, as shown. Hint: The base is designed to fit one way. If it does not seem to fit, turn it around and try again. Base Frame IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. 4 • Insert an M6 x 25 mm screw into the hole in the swing housing. Fully tighten the screw with the Allen wrench. • Repeat this procedure to assemble the remaining swing housing to the other frame tube. • Fit the tabs on the seat bottom into the slots in the seat back. 3 Seat Back Tabs Seat Bottom 4 Assembly 7 • Fit the end of each swing arm into the grooves in the seat. Groove Swing Arm Side View • Fit the side rails under the grooved areas under the seat, as shown. • Insert four #8 x 2,5 cm screws into the holes in the seat. • Tighten the screws with the Allen wrench. Side Rails 6 • Make sure the tab on each side of the seat back is fitted inside the socket on each side of the seat bottom. • Insert the hinge rod through the hinge on the seat assembly. • Insert a #8 x 2,5 cm screw into the end of the hinge rod. Tighten the screw with the Allen wrench. Hinge Rod Side View 5 Tab Tab • Insert a #8 x 2,5 cm screw into each swing arm. Tighten the screws with the Allen wrench. IMPORTANT! Push down on the seat assembly to be sure it’s secure to the swing arms. Swing Arms Side View 8 5 Assembly 9 10 • Insert the shoulder and waist restraint belts through the slots in the seat pad. Hint: The shoulder belts come assembled to the seat back in the lower slots for a smaller child. To change to the upper slots for a larger child, refer to page 10. • Insert the crotch restraint belt up through the slot in the seat pad. • Insertar el cinturon de la entrepierna en la ranura de la almohadilla. • Faire passer la courroie d’entrejambe dans la fente du coussin. Crotch Restraint Waist Restraints Shoulder Restraints 11 • Fit the pocket on the back of the seat pad onto the seat back. Side View Pocket 6 Assembly Elastic Loops Elastic Loops Tab Tab 13 • Fit the clips on the front edge of the seat pad to the front edge of the seat bottom. Clips Bottom View 12 • Lift the front edge of the seat pad and insert both elastic loops on the seat pad through the holes in the seat bottom. • From the bottom of the seat, hook the elastic loops to the tabs on the seat. 14 • Fit the notch in the seat pad around each swing arm. • Hook the seat pad elastic loops to the tabs on the seat. Swing Arm Elastic Loops wing 15 • Insert the end of the toy bar into the socket in the swing housing. Hint: The toy bar only fits one way. If it does not seam to fit, turn it around and try again. Toy Bar Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. T2065pr-0726 ©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA Battery Installation Battery Safety Information Hint: We recommend using alkaline batteries for longer battery life. 1,5V x 4 “C” (LR14) Swing/Sounds Battery Installation • Locate the swing/sounds battery compartment on a swing housing. • Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert four “C” (LR14) alkaline batteries into the battery compartment. • Replace the battery compartment door and tighten the screws with a Phillips screwdriver. Vibration Battery Installation • Locate the vibration battery compartment on a swing housing. 1,5V x 1 “D” (LR20) • Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert one “D” (LR20) alkaline battery into the battery compartment. • Replace the battery compartment door and tighten the screw with a Phillips screwdriver. • If this product begins to operate erratically, you may need to reset the electronics. Turn the power off and then back on. • When motion or sounds from the product become slow/faint or stop, replace the batteries. • Protect the environment by not disposing of this product...