Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. This unit is intended for display purposes only and should not be used for play. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts. Before beginning assembly, read the instructions and identify parts in this document. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. • During assembly, if using a ladder use extreme caution. Two people are recommended for this operation. • If technical assistance is required, contact Huffy Sports’ Sample and Display Technician. • Serious injury could occur if teeth/face come in contact with backboard, net or rim. • Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4” (10 cm) Square poles only. • All instructions and warnings MUST accompany any display item that is sold. Most injuries are caused by misuse and/or not following instructions. Use caution when installing this unit. REQUIRED TOOLS AND MATERIALS: • 2 People • Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4” or Pliers • Phillips Screwdriver • 2 Step Ladders, 8 ft. (2.4 m) IMPORTANT! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, problems may occur. To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display Technician at 414-820-3440. Internet Address: 1 06/03 P/N 211543B 1. 1. Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Display Stand - Top View Corner “2” 73603 Corner “4” 62959 Corner “3” 88603 Corner “1” 9H909A 2. Display boards will be mounted as follows: Corner Location 1: 9H909A • 44” SFA Board #909 • Hoop Time Logo • Black Slam Jam Goal • Exacta- Height Elevator System Corner Location 2:73603 • 44” Fan Recycled Board • Zone Attack Logo • Black Slam Jam Goal • Easyglide Elevator System Corner Location 3: 88603 • 44” Fan Recycled Board • Zone Attack Logo • Black Standard Goal • Exacta- Height Elevator System Corner Location 4: 62959 • 40” Fan Recycled Board • Street Heat Logo • Black Standard Goal • Extension Arm P/N 211543B 06/03 2 RIM ASSEMBLY Corner Locations 1 and 2 7 Assemble rims as shown below. 13. 5. 4. 3 4 8 2 3 06/03 P/N 211543B 6. Install net clips. Install net clips. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. CLIP “ARM” CLIP “BODY” 58 9 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping. A AA B BB C CC P/N 211543B 06/03 4 NET INSTALLATION SIDE VIEW NET NETCLIP 7. 58 9 10 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP 5 06/03 P/N 211543B 8. At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure the display pole (11), slide the display wedge (12) into position as shown. Tighten the set screw (13) to lock the display pole (11) in place. Use the second wedge only if necessary to tighten the fit. 12 13 11 9. At corner location 4 slide the display pole (14) (3 1/2” diameter) over the mounting pole stubs. 14 P/N 211543B 06/03 6 7 06/03 P/N 211543B 8 11 49 16 10. 11. 17 30 24 52 51 49 30 12. 49 8 55 54 54 57 44 57 55 13. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. Tighten flange nuts (8) completely. Attach spacers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown. IMPORTANT! Tighten until washers (30) no longer move. Attach covers (54) onto pole mount bracket (49) with carriage bolt (31) and nut (8) as shown. IMPORTANT! Loop end of pin lanyard (57) over carriage bolt (31) during this assembly. NOTE: Assemble lanyard (57) to locking pin (55) as shown. Apply logo and height indicator labels (48) to adjustment rod (47) as shown. Attach handle parts (45, 46) to adjustment rod (47) with screw (26), carriage bolts (22), and flange nuts (8) as shown. NOTE: Holes in adjustment rod allow for either rear access or side ...