Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
1 35 29 29 33 33 33 33 35 30 30 Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are required for this step, use caution, elevator assembly is heavy. 31 31 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 1 35 29 29 33 33 33 33 35 30 30 Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are required for this step, use caution, elevator assembly is heavy. 31 31 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 17. 35 31 33 33 30 30 Install handle assembly to long elevator tubes (30) using bolt (31), spacers (33), and nut (35) as shown. NOTE: Before going on to next step, adjust adjustable system assembly to the 10’ setting. 22 P/N 21145507 02/04 18. 31 29 29 Insert bolt (31) through left side short elevator tube (29), then stretch spring or springs (34) onto bolt (31). Insert bolt (31) through right side short elevator tube (29) and secure with nut (35). USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! 34 31 29 29 Insert bolt (31) through left side short elevator tube (29), then stretch spring or springs (34) onto bolt (31). Insert bolt (31) through right side short elevator tube (29) and secure with nut (35). USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! 34 35 1" (2.54 cm) CONCRETE 1 19. Secure pole end with tape (not included). Fill pole with concrete approximately 1” (2.54 cm) below bottom elevator hole as shown. NOTE: Make sure that concrete does not bulge from the end of pole assembly. Allow concrete to completely cure. Failure to fill your pole completely with concrete as described in these instructions will void all warranties written and implied. IMPORTANT!: IMPORTANT!: WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22. CONCRETE MUST CURE. 23 02/04 P/N 21145507 20. Install clips. CLIP “ARM” CLIP “BODY” USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. WARNING! 42 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping. A AA B BB C CC 41 24 P/N 21145507 02/04 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 21. 41 42 43 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 21. 41 42 43 25 02/04 P/N 21145507 IMPORTANT!: WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEPS. CONCRETE MUST CURE. PLAYING SURFACE 40 22. 4 After concrete has cured, remove tape, install pole cap (40), fit pole assembly into sleeve (4). IMPORTANT! Position pole assembly so the elevator assembly is perpendicular with playing surface. IMPORTANT! The elevator holes MUST be parallel with playing surface. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 5 23. Use wedge to tap cap of ground sleeve until tight. 26 P/N 21145507 02/04 27 02/04 P/N 21145507 Starting with nuts flush against bracket, secure rim and bracket to backboard. NOTE A: Do not use washers here on spring return style rim. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 1 41 WHEN MOUNTING THE BACKBOARD ASSEMBLY TO THE POLE IS PERFORMED AT AN ELEVATED HEIGHT. USE PROPER PRECAUTION. WARNING 24A. 24B. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING Starting with nuts flush against bracket, secure rim and bracket to backboard. NOTE A: Do not use washers here on spring return style rim. WHEN MOUNTING THE BACKBOARD ASSEMBLY TO THE POLE IS PERFORMED AT AN ELEVATED HEIGHT. USE PROPER PRECAUTION. WARNING IMPORTANT! Refer to instructions included with board and rim hardware for backboard and rim assembly, Note A Note A 41 IMPORTANT! Refer to instructions included with board and rim hardware for backboard and rim assembly, 25. 25. A. While holding handle, remove pin (26). 26. Apply height adjustment label (38) B. Move elevator up or down to desired to front of pole as shown. height. Regulation rim height is 10 feet C. Replace pin (26) full length to lock (3.05 m). system at desired height. DO NOT ALLOW CHILDREN TO ADJUST HE...