Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Refer to the parts and fasteners pages for identification. Keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Ages 18 months – 5 years. Maximum weight: 50 lbs. (23 kg). Tools needed for assembly: Hammer, Phillips Screwdriver and Scrap Block of Wood (not included). This product requires three “AAA” (LR03) alkaline batteries (not included) for sound box operation. If you have any questions about this product, or are missing a part, please contact Fisher-Price® (online at or call toll-free at 1-800-432-5437) rather than return this product to the store. Bounce ‘n Go™ Coupe Parts Parts Handle/Canopy Notes: • Some parts shown are assembled to both sides of the coupe. • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry cloth before assembling this product. • Part not shown: label sheet. Upper Post Sound Box Cover Sound Box .354" Cap Nut Steering Wheel Turn Signal Steering Wheel Base 2 Axle Covers 2 .354" Cap Nuts Frame Latch Halves Grip Halves Seat Lower Post Rear Axle Footrest Steering Column Steering Linkage Assembly - Fitted to Frame (with Front Axles) 2 5/16" Washers 2 Frame Bushings 2 Small Front Wheels 4 Wheel Bushings 4 – .354" Cap Nuts Assembly Tool Bouncing Base/Spoiler 4 Axle Bushings 4 Axle Covers2 Large Rear Wheels 2 Warning and Caution Fasteners Warning and Caution Fasteners Note: We’ve included extra fasteners for your convenience! .354" .354" Cap Nut - 7 5/16" Washer - 2 #6 x 1/2" Screw – 6 CAUTION WARNING To avoid serious injury: • Adult supervision required. • Never use near cars and other motor vehi- cles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools, or other bodies of water. • Always wear shoes or sneakers • Never allow more than one (1) rider. This product contains small parts in its unassembled state. Adult assembly is required. #8 x 3/4" Screw – 11 1/4" x 11/4" Screw – 1 #10 x 21/8" Bolt – 1 ALL SHOWN ACTUAL SIZE Note: Tighten and loosen all screws and the bolt with a Phillips screwdriver. Do not over-tighten the screws and bolt. 3 1 • Place the frame upside down on a flat surface. Make sure the steering linkage assembly is fitted to the front end of the frame. • Remove the tape holding the front axles to the frame. Rotate the front axles out. 3 • Fit the peg on the footrest into the hole inside the frame. • Insert the 1/4" x 11/4" screw into the footrest and tighten. Assembly Steering Linkage Assembly Frame Front Axles Footrest Peg Bottom View 1 • Place the frame upside down on a flat surface. Make sure the steering linkage assembly is fitted to the front end of the frame. • Remove the tape holding the front axles to the frame. Rotate the front axles out. 3 • Fit the peg on the footrest into the hole inside the frame. • Insert the 1/4" x 11/4" screw into the footrest and tighten. Assembly Steering Linkage Assembly Frame Front Axles Footrest Peg Bottom View 2 • Push the front axles down into the groove in each end of the steering linkage. PUSH Groove Groove PUSH 4 • While holding the steering linkage assembly in place, carefully turn the frame upright. • Fit a .354" cap nut onto the upright end of a front axle. • While holding the front axle in place, tap the cap nut with a hammer to secure it to the front axle. Pull up on the cap nut to be sure it is secure. Hint: You may need the help of another adult to hold the front axle in place while you tap the cap nut with a hammer. • Repeat this procedure to assemble another cap nut to the other front axle. .354" Cap Nuts Front Axles .354" Front Side View 4 5 Axle Covers Assembly 5 Axle Covers Assembly 7 Small Front Wheel • Locate both small, front wheels. • Slide a small, front wheel, flat side first, onto the front axle. • Fit an axle cover over the cap nuts and to the front end of the frame. Push down on the axle covers to “snap” them into place. Hint: You may need to carefully tap the axle covers with a hammer to secure in place. 6 5/16" Washer Axle BushingFront Axle • Slide a 5/16" washer onto a front axle. • Next, fit an axle bushing, barrel side first, onto a front axle. 8 • Fit a wheel bushing, peg side first, into the small, front wheel and onto the front axle. Wheel Bushing 5 Assembly Assembly 9 .354" .354" Cap Nut Assembly Tool • Fit a .354" cap nut onto the end of the front axle. • Cover the cap nut with the assembly tool. Tap the cap nut assembly tool with a hammer to secure the cap nut to the front axle. • Pull on the small, front wheel to be sure it is secure on the front axle. 11 • Lift the back end of the frame up slightly. • Position the bouncer base/spoiler so that the columns are upright and the “U” shaped cut-out is toward the back of the vehicle. • Now, lower the back end of the frame onto the bouncer base/spoiler tabs. Make sure the tabs on the bouncer base/spoiler fit into the grooves in the frame. Back End of Fr...