Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
Check wheels are fully engaged by gently trying to pull them out. Hold handle and lift upwards until stroller frame is fully extended and clicks into position. Push front swivel-wheel assembly into front leg. Listen for a positive “click” to ensure the wheel is correctly fitted. When properly fitted, the screw head on the front swivel-wheel assembly should face forward and the wheel’s solid spoke fronts should face outward. Pull down gently on the wheel to ensure it is fully engaged. Repeat process for remaining front wheel. Push down on parking brake lever to lock brakes. To release brake, lift parking brake lever. IMPORTANT: Always engage parking brake when fitting seat unit. To unlock swivel wheels, pull front wheel swivel lock lever up on each front wheel. To lock, align wheels to rear of front leg and push lock down. To install seat unit (forward or rear facing), store infant carrier attachment bar. (See section 3.) Slide hooks at foot end of seat unit onto stroller support bar until hooks are fully engaged with support bar. WARNING: Always remove child from seat unit prior to installation, removal or change of seat direction. 1j 1k 1nDACDBB 1o 1l 1m 1i To secure child in harness, slide each waist clip (A) into buckle (C) until prongs snap into position. Clip harness belt hooks (B) onto waist belt clip. Carefully adjust harness by pulling sliders (D) until desired fit is achieved in waist, shoulder and crotch straps. WARNING: Always use crotch strap in combination with waist belt. Fasten harness when not in use to prevent it from becoming trapped when folding the stroller. To attach arm bar, align arm- bar moldings with plastic tabs on seating unit and slide both arm-bar moldings onto seating unit until fully engaged. Ensure arm bar is securely in place by gently pulling on it. To remove arm bar, remove hood (if fitted) and slide both arm-bar moldings off plastic tabs on stroller frame. WARNING: NEVER lift stroller by the arm bar or hood as they may disengage. If needed, lift stroller by handle and stroller frame. To raise shoulder harness height, pull harness straps through harness height adjuster so that they lay flat on top of the harness height adjusters. To lower shoulder harness height, thread harness straps through harness height adjuster so they lay flat against the seat back, under the harness height adjuster. To fit hood, align moldings with plastic tabs on arm bar and slide down until fully engaged. Hood can be fitted without arm bar by aligning hood moldings with plastic tabs on seat unit and sliding down until fully engaged. To adjust the angle of the seating unit, squeeze recline adjuster lever at top of seating unit, then adjust seating unit to desired position. IMPORTANT: Use harness at all times. Always support back of stroller seat when reclining it. To open hood, pull front of hood forward then push hood hinges down on both sides. To close hood, lift up hood hinges on both sides and push front of hood back. Rotate seating unit downward until seat locking clips fully engage with the opposite bar. WARNING: Check that seating-unit attachment devices are correctly engaged before use. 3. Using as a travel system Britax Companion® Click and Go™ easy-assembly method vigour 2. Folding and storing the stroller 3c 3b 2c 2d 2e 2a 2b 3a 4b To remove carrier, squeeze release lever on back of seat while lifting carrier from stroller. Pull carrier attachment bar away from front stops and swing it back so that it rests against the front of the storage basket. Remove seat unit. (See diagram 2a.) Swing carrier attachment bar (hanging near front of the storage basket) forward until it engages with the stops affixed to the front of the stroller frame. IMPORTANT: When using as a travel system, always remove infant carrier prior to folding of stroller. WARNING: Apply parking brake when attaching or removing your infant carrier. (See diagram 1f.) Lower the carrier rear facing with attachment hooks aligned with attachment bar. Press carrier onto attachment bar until a positive click is heard. IMPORTANT: To ensure proper installation, pull up on carrier by the handle (in carrying position) to verify both attachment hooks are engaged with the attachment bar. WARNING: Check that carrier attachment bar is correctly engaged before use. WARNING: Ensure your child is harnessed at all times. WARNING: NEVER lift the stroller by the infant carrier. Stand at rear of stroller frame, pull both release latches and twist right hand latch in the direction of arrow marked on release latch. For more compact storage, fold handle down. (See diagram 1e.) For more compact storage, remove front swivel wheels. Slide front wheel locking button toward the middle of the stroller, then pull corresponding swivel wheel out. To remove seating unit, apply parking brake. Release both locking clips from support bar by lifting and holding both seat- locking clips. Raise rear of seating unit clear of support bar, then slide seat unit forward ...