Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
introductionwatch fingers when folding - folding mechanism could be a pinching hazardLay the stroller flat on the fork tubes, as shown. Remove the rubber protectors from the ends of the forks and thumb tabs. assemblypocketssuspensionRebound GST™ model onlybasketcanopy windowwater bottleholdershand brakeindependently rotatingsun canopiesdual foot platesfront quickrelease wheelfork tipsthumb tabsharnessrear wheelpush buttonAll Weather CoverBike Pump(not pictured) fork tip protectorthumb tab protector foam protectorpush buttonMake sure the foot brake is in the unlocked, up, position. To put the rear wheels on, push the button on the wheel while pushing the wheel axle into the stroller frame. Remove and discard the foam protectors on the wheel axles. be sure to discard the plastic bags from the wheels - they are a suffocation hazard for childrencheck to make sure the wheels are secure before each useassemblyUnfold the frame and insert the thumb tabs into the slots. Fold the plastic swing clasps in, to latch around the frame. Tip the stroller back so it is resting on its handle and rear wheels to put the front wheel on. Make sure the brake release lever is pointed out, away from the stroller.lever pointed outthumb tabsswing clasp Starting at the bottom of the brake pads, push the wheel up and in between the brake pads. The quick release lever should be straight out. While holding the lever, tighten the thumb nut until it is barely snug. The axle should not move side to side. Rotate the tire upwards and find the flat sides on the round axle and slide all the way to the back of the forks, on BOTH assemblyPush the quick release lever down so it is flush with the frame. Give the wheel a tug to make sure it is secure. Be sure to close the brake calipers by pushing the lever forward all the way. flat sidebrake padsthumb nutquick release levercheck to make sure the wheel is secure before each uselever forwardcheck to make sure the brake caliperis locked before each use To lock the hand brake, pull the lever in and hold it while you push the button down. As you hold the button down, release the brake lever. Your stroller comes with two parking brakes: a foot brake and a hand brake. The hand brake, located on the handle, locks the front wheel. The foot brake is located near the basket, on the rear axle. It locks the rear wheels. brakesTo release the hand brake pull the lever in until the button pops up. NEVER trust your brakes 100%! Always keep an eye on your stroller. Always use your safety wrist strap any time a child is in the stroller. check to make sure the brake caliperis locked before each usePull the foot brake up with your foot to release it. To lock the foot brake you simply push it down with your foot. Then try to push the stroller to make sure the brake is secure. If the front wheel still moves, see the brake adjustment section on page 24You should always use both brakes when the stroller is not being pushed. leverpush buttonreleasing brakebrake unlocked Your canopy has multiple adjustments. It also has a side ventilation system, with flaps that roll up and velcro into place. To bring the canopy to it's next position, flip the mesh portion under. Use the canopy at it's fully extended position during midday sun to provide your child with the most amount of shade. bubble sun canopy™ When the canopy is not needed, pull it all the way back. To view your child through the top window, simply roll back the sun cover and velcro into place. To clean the canopy window use a damp cloth. To shade your child during early morning or late evening sun, unsnap the strap at the back of the canopy, and pull it all the way forward. stationary strapunscrew To remove the sun canopy you will need a Phillips screwdriver to remove the screws from both sides of the canopy. Unsnap the canopy from the back and lift it out. Before washing the canopy, remove the frame. The canopy may be washed in cold water with mild detergent. Place the canopy back on the stroller to dry. bubble sun canopy™ seatThe amount of recline on the seat is adjusted by holding the buckle behind the seat and pull the strap to make the seat more upright. The seat is fully reclined by unbuckling the strap behind the seat. The seat is removed by undoing the velcro and the straps from the foot plate and the frame. The seat also needs to be unsnapped from the frame. To make the seat recline more, hold the strap and pull the buckle. unscrew hereIt may be snug, but it will lift out. When the canopy is wet, extend it fully until completely dry to prevent any mildew from forming. WARNING Child may slip into leg opening and strangle. Never use in reclined position unless the firmness panel is in place. adjustment strapvelcro strapssnap To wash the seat take out the firmness panels by unzipping the pouch at the top and underneath the seat. Do not remove the firmness panels when using your stroller. Removing the panels could cause suffocation. seatharnessUndo both buckles from...