Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Ask them to read instructions completely. Operating Instructions Important:Read and follow these Safety Rules and Assembly Instructions before operating stroller. If you have any questions concerning the safe use of this product, contact Pacific Cycle LLC at 1-800-242-6110, M-F, 8:00 a.m. – 5:00 p.m. C.T. or visit our website at Safety Rules: WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Immediately discard any plastic wrapping. Never allow children to fold, assemble, or disassemble the stroller. Maximum weight capacity for the Single stroller is 50 lbs. or 22.7 kg. Excessive weight may cause a hazardous, unstable condition if this load is exceeded. Maximum height of the child shall not exceed 38" or 96 cm. Never place child in stroller with their head forward and feet rearward. Avoid serious injury from falling or sliding out. Always use seat belt. Never leave child unattended. Never use this stroller with roller or in-line skates. Never allow stroller to be used as a toy or allow children to give rides to others. Never use stroller if it becomes damaged. Always be aware of traffic around you when walking. Always engage brakes when you stop or when you let go of handle. Accessories or parcels placed in or on the stroller may cause it to become unstable. Maximum weight for objects in bottom basket is 5 lbs. or 2.2 kg. Excessive weight may cause a hazardous, unstable condition. Maximum weight for objects in rear zippered pouch is 1 lb. or .45 kg. Excessive weight may cause a hazardous, unstable condition To avoid burns, never put hot liquids in the parent or child tray. To prevent tipping over do not place more than 2 lbs. or 1 kg on either the parent or child tray. Child may slip into leg openings and strangle. Never use in a reclined carriage position unless T-shield/ waist strap placement has been readjusted. Care must be taken when folding and unfolding the product to prevent finger entrapment. IMPORTANT We appreciate your purchase of one of our many fine products. We are sure that you will be satisfied with your selection. We regret that although great care and effort have been taken, occasionally problems may occur. PLEASE DO NOT RETURN PRODUCT TO THE STORE. To ensure prompt and correct handling of problems, or to answer questions, please contact us at either our Toll-Free Customer Service number or E-mail us at our address listed below. Service will be quicker if you have your model number (found on the product and box) along with this instruction sheet ready when calling. If you have any questions concerning the safe use of this product, please contact us at 1-800-242-6110, and follow the prompts to our customer service representative, or E-mail us at info@instep.net or visit our website at Tires are shipped deflated, DO NOT OVERINFLATE. Please inflate slowly, with short bursts, to 30-35 PSI maximum. 30 PSI will provide a comfortable ride for your child Model M3 Strollers Assembly InstructionsParts List Description Qty Frame Assembly 1 Fender 1 Fender screws # 8 x 3/4" 4 Parent Console 1 Front Wheel Assembly 16" 1 Rear Wheels 16" 2 Stroller Assembly InstructionsStep 1. Unfold Stroller Grasp frame as shown and open until both side latches engage (Figure A). Step 2. Rear Wheel Assembly Turn stroller onto its side. Grasp rear wheel in one hand, slide wheel’s axle into the sides of the rear “ U “ shaped crossbar hole located near the rear brake. Push firmly to lock in place. (Figure B1). Check to see that the wheel is properly inserted by pulling on the wheel firmly. The wheel should not come off if fully inserted/locked. Repeat for other side. To release wheel push up on axle release lever and pull off wheel (Figure B2). Fig. A Fig. B1 Fig. B2 Rear Axel Axel Hole Release Lever Step 3. Front Fender AssemblyTurn stroller upright onto its rear wheels, then tip stroller back so the handlebar is down on the ground and the front fork is up. Align the fender’s 4 boss’s with the 4 holes on the front frame push the 4 boss’s into the frame’s hole. Insert the #8 x 3/4" screw into the hole and tighten with a Phillips screwdriver, repeat for the other 3 holes (Figure C). Fig. C Boss Front Fender Holes Step 4. Front Wheel Assembly While stroller is still tipped back, attach the front wheel by loosening the wheel’s quick release (Q/R) lever on the front wheel far enough to allow the axle to slide into the front fork (Figure D1). The front caliper brake Q/R lever should be in the open position so the front wheel can be inserted easily Into the front fork . With wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight, then close the wheel’s Q/R lever to lock wheel in place. Note this step may require minor adjustment until the Q/R lever flips back with firm pressure ( Figure D2 and D3). Pull outward on wheel to ensure it is locked in place. Close the Q/R lever on the front caliper brake and spin the fro...