Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
The tinted glass will make the stained wood appear darker. A true color match can be seen only when the door is opened. • Apply the stain and sealer according to the manufacturer’s instructions. To avoid unpleasant odor, keep the door open to ventilate and allow the stain/sealer to dry completely before using the product. STEP 1 REMOVE PACKAGING • Remove corner blocks and foam drawer stops. • Remove all packing material, tape and protective plastic coverings. • Remove stainless steel toekick taped to the back of the unit. CAUTION: Small objects are a choke hazard for children. Remove and discard any parts not used. MISE EN GARDE : Les petits objets peuvent etrangler les enfants. Il faut jeter toutes les pieces qui ne sont pas utilisees. 4 Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Parts Included: • Top left case hinge • Bottom left case hinge • Left and right side decorative hinge cover • Decorative hinge screw hole cover • Torx® driver bit Tools Required: • Phillips screwdriver • Electric drill Remove the door: • Flatten the shipping carton to use as a pad. • Remove the 2 screws and the toekick. Set aside the screws and toekick for final installation. • Use the supplied Torx® bit and electric drill to remove the 3 screws holding the top case hinge. Lift off the hinge. (Screws will be used to install the new hinge.) • Lift the door off the bottom case hinge. • Remove the bottom case hinge pin and bracket. Rotate the door: The handle will be on the right side of the door; hinges will be installed on the left side of the case. • Remove the door stop and cam riser on the original bottom right side of the door. • Remove the fill plug on the top right side of the door. • Turn the door over and reinstall the fill plug on the new left side. Reinstall the door: • Install the original door stop and cam riser onto the bottom left side of the door. • Install the new supplied bottom case hinge pin and bracket onto bottom left side. • Place the door onto the bottom case hinge. • Install the supplied left-hand top case hinge with the 3 original screws. • Select the hinge cover marked with an “L”. • Peel backing off the tape inside the decorative hinge cover. • Press and snap the hinge cover into place. • Snap the screw hole cover into place on the opposite side. IMPORTANT: Check to be sure screws are tight and that the door is straight and does not sag. The door should swing freely. Apply Monogram Nameplate: • Install the Monogram nameplate. See instructions and template on back cover. Install Toekick The toekick has a cutout on the left and right sides. Remove the plug on the left side and reinstall on the right side. If you choose to install the stainless steel toekick, reinstall the plug on the right side of that toekick. • Install original screws and spacers or screws and spacers supplied with the stainless steel toekick. Install screws through the spacer standoff, toekick and into the base as shown. Move Fill Plug to Right Side Remove Top Hinge Remove Hinge Install 3 Hinge Screws Door Stop and Cam Riser Hinge Pin and Bracket Install Covers 5 Installation Instructions STEP 3 LEVEL • Use an adjustable wrench to turn the leveling legs and raise or lower the product. • Adjust carefully; the product should be level and plumb with cabinetry, and should align with adjacent toekick height. STEP 5 SLIDE PRODUCT INTO THE CUTOUT • Carefully, slide the unit into the opening. Be careful not to entangle power cord. • Make certain that the door protrudes 1. beyond the surrounding cabinets. • Check again to be sure the unit is level. STEP 4 CONNECT POWER • Connect power cord plug to a properly grounded receptacle. • Check to make sure power is on by opening the door to see if interior light turns on. STEP 6 INSTALL NAMEPLATE • Follow instructions on the back page for installation of the Monogram nameplate. STEP 7 SET TEMPERATURE CONTROLS • The temperature controls are preset. Refer to the Owner’s Manual for more information. Allow 24 hours for temperature to stabilize. Turn Right to Lower Turn Left to Raise If you skipped Step 2: • Select the hinge cover marked “R” or “L”, depending on door swing. • Peel backing off the tape inside the decorative hinge cover. Press and snap into position. • Snap the screw hole cover into place on the opposite side. 6 7 TEMPLATE FOR NAMEPLATE LOCATION To position nameplate: • Cut template along dotted line. • Hold or tape template behind glass door so that it is visible from the front side. • Remove backing from nameplate. • Place nameplate onto front side of door, matching illustration on the template. IMPORTANT: Nameplate must be placed on the opposite side of the door handle. Top of Badge Cut on Dotted Line Top of Glass Door Door Frame Side Upper Left Corner of Glass if Hinge is on Left DOOR NAMEPLATE LOCATION Upper Right Corner of Glass if Hinge is on Right Door Frame Side TEMPLATE FOR NAMEPLATE LOCATION To position nameplate: • Cut te...
Otros modelos de este manual:Dispensers - Wine Chiller Wine Reserve and Beverage Center (169.41 kb)