Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
This simple test can be done quickly by your dealer. The Good Water SentryTM Water Quality Monitor is another way to keep track of your system’s performance. This optional accessory checks your drinking water each time you use the special faucet, and signals when the membrane filter may need to be replaced. If the water quality of your system seems to have declined, drain the storage tank and allow the system to refill. If the problem persists, call your Culligan Man for service. INSTALLATION This Owner’s Guide provides visual assembly reference only. Since specialized skills are required in the assembly of the drinking water system, we recommend that you contact your local independently operated Culligan dealer to complete this installation. APPLICATION GUIDELINES The Good Water Machine is designed for use on potable water supplies ™ meeting the guidelines outlined in Table 1. The system should be installed on your home’s cold water line. The flushing stream should discharge through an approved siphon break as illustrated in Figure 1. Installation of this system must comply with state and local laws and regulations. TABLE 1 Influent Water Characteristic Pressure 40 -120 psi (280 - 827 kPa) Temperature 33 -100°F (1 - 38°C) Total Dissolved Solids (TDS)1 0 - 4000 ppm ( 0 - 4000 mg/L) pH 5 - 10 Chlorine2 0 - 3 ppm ( 0 - 3 mg/L) Chloramine 0 - 3 ppm ( 0 - 3 mg/L) Turbidity 0 - 10 NTU Iron 0 - 1 ppm (0 - 1 mg/L) Bacterial Quality Potable 1 See the Technical Manual for all applications where TDS exceeds 1000 ppm (1000 mg/L). A booster pump is strongly recommended. 2 The reverse osmosis membrane filter used in this system may be damaged by chlorine. This system includes activated carbon which protects this element by reducing chlorine. Influent chlorine should not exceed 3 mg/L. Fig. 1 1. Particle Filter* 2. Activated Carbon Filter* 3. Reverse Osmosis Membrane Filter 4. Polishing Filter 5. Tubing Tee 6. Storage Tank 7. Faucet 8. Cold Water Line 9. Water Shutoff *Combined Particulate/Activated Carbon Filter on Model H-30S-R SERVICING YOUR SYSTEM SERVICE SCHEDULE When properly maintained, your Good Water Machine will give you years of ™ dependable service. Use the following as a guide to get the most out of your system. Service frequency may vary depending on your local water conditions. High sediment, chlorine, turbidity, or hardness levels may require more frequent service. Refer to Figures 4 & 5, on page 9. At Least Once Per Year Replace: • Particle/Activated Carbon Filter(s) • Polishing Filter Check: • RO Membrane Filter - TDS Reduction Performance -Flow Rates • Capillary Assembly Sanitize the System. Use the convenient chart inside the back cover of this booklet to keep track of your system’s maintenance. FILTER REPLACEMENT Culligan recommends that you have your Good Water Machine serviced by your local Culligan Man. You can rely on his or her experience and expertise to keep your system in top operating condition. If you wish to service your system, the filters are available from your Culligan dealer. See the Parts List at the end of this section for replacement numbers. Cartridge Conditioning The activated carbon, reverse osmosis, and polishing filter cartridges must be conditioned as follows prior to installation into the Good Water Machine. Your Culligan Man can do these important procedures at the time of purchase. Activated Carbon Cartridge - 5 gallon flush to remove carbon dust RO Membrane Filter - 6 hour flush to remove preservative solution Polishing Filter - 2 gallon flush to remove carbon dust Fig. 3 Fig. 2 Fig. 3 Fig. 2 Tubing Connectors The Good Water Machine system features two simple types of tubing ™ connectors. Tubing can be connected easily as follows: Push-in type (Fig. 2) To connect, lubricate the tubing end with water and push the tubing into the connector until it bottoms out. Be sure the tubing is smooth and free of scratches, otherwise a leak my result. To disconnect, hold the collar against the fitting body and pull the tube from the fitting. Threaded type (Fig. 3) To connect, assemble the fitting parts onto the fitting, leave the nut loose, and push the tubing firmly into the fitting until it bottoms out. Hand-tighten the nut. To disconnect, loosen the nut and pull the tubing from the fitting. Fig. 4 Fig. 5 Fig. 4 Fig. 5 Filter Replacement and Sanitizing Procedure Use the following procedure and reference in Fig. 1, 4 & 5 when servicing the Good Water Machine ™. NOTICE: You may want to fill a pitcher with drinking water before beginning service as it will take several hours for the system to refill after servicing. The Good Water Machine may be sanitized with either 5-1/4% liquid chlorine bleach or a fresh bottle of consumer grade hydrogen peroxide. NOTICE: The reverse osmosis membrane filter used in this system may be severely damaged by chlorine. The membrane filter must be removed from the system if chlorine bleach is to be used for sanitizing. NOTICE: Hydrogen peroxide should not b...