Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
2. Position the unit on a stable flat surface, close to a main power outlet. Avoid direct sunlight and keep out of the reach of children. 3. Allow at least 3 inches of space around the sides and rear of the unit for proper air circulation. 4. Remove filter from upper tank and carefully follow the SETUP instructions below. You will need a large bowl, a pitcher (or another type of container) and a glass. NOTE: Do not plug in unit until ALL steps of SETUP are complete. WATER FILTER SETUP NOTE: For optimum filtering and flow rates, the water filter must be prepared and installed exactly as follows: Preparing the Water Filter 1. Remove the filter from its packaging. NOTE: The filter may contain a small amount of loose carbon dust. It may also appear moist, have a faint smell of plastic or a slight yellowish tint – these are all normal. DO NOT wash filter with soap or water. 2. Place water filter in bowl, and being careful not to pour water directly onto the filter. Slowly add enough cold water to fully submerge and cover the filter by at least 1 inch. (You should see bubbles escaping the filter.) 3. Continue to hold filter under water for at least 30 seconds. 4. Release the filter and let it soak at least 15 minutes. NOTE: While soaking, the filter should be partially submerged and may tilt to one side. Installing the Prepared Water Filter 1. While the filter is soaking, remove the lid, upper water tank and lower water tank. empty bowl sideways (see image). Pressing it firmly to the bottom of the 2. Remove the filter timer from the lid by flipping the lid over and pressing on the plastic tab. 3. Wash both tanks and plastic lid in mild, soapy water, and rinse. Replace the filter timer. 4. Lift the filter from the bowl and allow water to drain. NOTE: The filter's loose carbon dust may slightly darken water while soaking. 5. With the Cuisinart® logo facing up, insert the water filter into the upper water tank and push firmly into place. 6. Place the upper tank on a pitcher (or another type of container) and fill with cold tap water. Allow to drain for 5 minutes to flush out any remaining carbon dust, then pour out remaining water. WATER DISPENSER SETUP NOTE: Use only cold tap water to fill the unit. Filling the Upper and Lower Tanks 1. Place the upper tank onto the lower tank and cover with the lid. Lid Upper water tank Lower water tank 2. Place assembled tanks on base. NOTE: The vertical groove on the upper tank must face the back of the unit. 3. Carefully lift the flip top lid and add cold water to the FILL line. NOTE: This is a gravity fill system. To increase the filtering flow rate, continue adding water to the FILL line of the upper tank until tanks are completely full. 4. During the initial setup, allow 20–30 minutes for water to filter into and completely fill upper and lower tanks. Filling the Internal Tank NOTE: Upper and Upper lower tanks must be Tank completely full before proceeding. Lower Tank 1. Place a glass under the spigot and press and continue to hold the COLD button until water flow becomes steady (may take up to 3 minutes). 2. Repeat process with ROOM button until both flow steadily. NOTE: When filling the cold internal tank, the water level in the lower tank will drop and you will hear the filling process taking place. Setting the Filter Timer The filter timer, located on the lid of the unit, lets you know when to change your water filter. Each filter will last for 3 months. 1. Once unit is set up and all water tanks are full, peel off the FILTERINg sticker from the filter timer screen. 2. Press and hold the Start button until FILTERINg is displayed (approx. 3 seconds). 3. In 12 weeks, the word REPLACE will appear. For best results, we recommend inserting a new Cuisinart® Water Filter immediately. 4. You may turn off the timer and display by pressing the Start button for 5 seconds. Once you replace the filter, reset the timer by pressing the Start button for 3 seconds. NOTE: You may reset the timer at any time by pressing and holding the Start button for 3 seconds. OPERATING INSTRUCTIONS Once setup is complete, tanks are filled and water is flowing steadily, your unit is ready to use! 1. Close the lid and plug unit into outlet to activate the cooling function. 2. After about 1 hour and 20 minutes, the BLUE cold water indicator will light up, signaling water is chilled. NOTE: On subsequent fill-ups, unit should take less than 30 minutes to chill. 3. Press and hold each button to ensure all air has been purged from the unit so water flow is steady. REPLACING WATER FILTER Replacement filters may be purchased at most retail outlets or To replace your filter, follow “Water Filter Setup” on page 4. TIPS AND HINTS • Drinking 4 to 8 glasses of water each day is healthy! Your countertop chiller makes it easy. • Regular use of cleaner, filtered water in your automatic coffeemaker means less frequent decalcification treatments. • Use filtered water in your iron to reduce mineral build...
Otros modelos de este manual:Dispensers - IB-8895A (2.03 mb)